10 More Discussions You Might Find Interesting
1. AIX
Hi Guys,
I have fresh new installed VIO 2.2.3.70 on a p710, 3 physical SAS disks, rootvg on hdisk0
and 3 VIO clients through vscsi, AIX7.1tl4 AIX6.1tl9 RHEL6.5ppc, each lpar has its rootvg installed on a LV on datavg (hdisk2) mapped to vhost0,1,2
There is no vg on hdisk1, I use it for my... (1 Reply)
Discussion started by: frenchy59
1 Replies
2. Solaris
I have written a virtual HBA driver named "xmp_vhba". A scsi disk is attached on it. as shown below:
xmp_vhba, instance #0
disk, instance #11
But the performance became very bad when we read/write the scsi disk using the vdbench(a read/write io tool).
What is the reason? ... (7 Replies)
Discussion started by: ForgetChen
7 Replies
3. Solaris
Hi, I tried this question on OTN Discussion Forum, but it seems that forum doesn't have as much activity so I thought I'd try here.
I have a big performance problem with Samba server on a fresh install of Solaris Express 11 svn_151a, and a freshly created ZFS pool. I'm getting about 3 to 10 MB/s... (2 Replies)
Discussion started by: doublemeat
2 Replies
4. AIX
Hello,
Script command helps to save command output to file. (Redicection doesn't work in this case).
Besides interactive shell 'recording', Linux script command has "-c" option which allows to record output of some non-interactive command.
The problem is that AIX script command variant... (6 Replies)
Discussion started by: vilius
6 Replies
5. AIX
I'm trying to run a compress script in the background, but I even though the script is running in the background I get "Sending nohup output to nohup.out." and the screen just stays there. How can I make the script run in background and make my command prompt come back.
I was using:
nohup... (2 Replies)
Discussion started by: NycUnxer
2 Replies
6. HP-UX
There might be some problem with my server,
because every morning at 7, it's performance become bad with no DB extra deadlock.
But I just couldn't figure it out.
Please give me some advise, thanks a lot...
According to the CPU performace chart, Daily CPU loading Maximum: 42 %, Average:36%.
... (8 Replies)
Discussion started by: GreenShery
8 Replies
7. UNIX for Dummies Questions & Answers
Hi..
Can anybody tell me, what exactly the nohup command does & when is it used?
Your help is appreciated. (3 Replies)
Discussion started by: Amol21
3 Replies
8. AIX
Hello guys!
I'm n00b in AIX and I'm sticked in a problem. (my English is poor enough, but I hope you can understand me :P). So.. I'm trying to connect to an AIX machine with putty, and .. 'using username xxx' appears after 2 sec (OK), but 'xxx@ip's password' appears after 1:15 min. After... (6 Replies)
Discussion started by: combat2k
6 Replies
9. UNIX for Dummies Questions & Answers
Hi All,
Can you please help me in resolving the following problem?
My requirement is like this:
1) I have two files YESTERDAY_FILE and TODAY_FILE. Each one is having nearly two million data.
2) I need to check each record of TODAY_FILE in YESTERDAY_FILE. If exists we can skip that by... (5 Replies)
Discussion started by: madhukalyan
5 Replies
10. UNIX for Dummies Questions & Answers
Hello All,
I am newbie to unix.I am trying to use NOHUP command in shell script it works fine with only "nohup test.sh 10 &" and "/opt/user/nohup test.sh 10 &" gives an error saying "ksh: /opt/user/nohup : not found".
Can anybody please guide me to make it work.
Thanks
Blazix (9 Replies)
Discussion started by: blazix
9 Replies