10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hello,
i have a system with 6 sata3 seagate st3000dm01 disks running on stable Debian with software raid mdadm. i have md0 for root and md1 for swap and md2 for the files. i now want to add one more disk = sdh4 for md2 but i got this errors:
The new disk is connected to an 4 port sata... (7 Replies)
Discussion started by: Sunghost
7 Replies
2. UNIX for Dummies Questions & Answers
hi power went out. next day unix sco wont boot up error code 303. any help appreciated as we are clueless. (11 Replies)
Discussion started by: fredthayer
11 Replies
3. Red Hat
I am configuring Samba on one of my vmware.when i put smbclient -L local its showing error message : NT_STATUS_LOGON failure.I found that when i remove "Encrypted password entry from smb.conf" it works.
pls help me
---------- Post updated at 08:39 PM ---------- Previous update was at 07:11 PM... (0 Replies)
Discussion started by: Vaibhav.T
0 Replies
4. Shell Programming and Scripting
Hello,
Sometimes when i execute my shell that makes sftp it gives me this error:
Couldn't close file: Failure.
What does it mean?, how can i make sure it will do ok?.
Bye (2 Replies)
Discussion started by: rubber08
2 Replies
5. Solaris
Our Solaris was hung yesterday, and dmesg show that,
nxge3 : <== nxge_m_start: initialization failed
nxge2 : nxge_dma_mem_alloc:ddi_dma_mem_alloc kmem alloc failed
nxge2 : nxge_alloc_rx_buf_dma: Alloc Failed: dma 9 size_index 10 size requested 4194304
Does it mean the DMA failure ? How... (5 Replies)
Discussion started by: dehetoxic
5 Replies
6. UNIX for Dummies Questions & Answers
Dear Members,
I have a file which contains ControlM characters in it.
I need a command by the means of which i should be able to identify if a file has controlM characters.
How can this be achieved.
Thanks
Sandeep (4 Replies)
Discussion started by: sandeep_1105
4 Replies
7. UNIX for Advanced & Expert Users
Usually when su rejects an attempt to switch user it responds with "Sorry" but with a certain username on some unix servers the response is "Killed". I'm guessing the su accepted the username/password but refused to spawn child shell with the specified username. What's causing this and what has to... (8 Replies)
Discussion started by: twk
8 Replies
8. UNIX for Advanced & Expert Users
I'm trying to change the user Id that the script is running under. I tried the sudo comand but the job was submitted under ControlM and it seems that controlM is not allowing the user id to change. I have included the job output below. The sudo comand was suppose to set the user id to "DWSOLAP"... (3 Replies)
Discussion started by: u156531
3 Replies
9. SCO
Forgive me, I do not know much about RAID so I'm going to be
as detailed as possible.
This morning, our server's alarm was going. I found that one
of our drives have failed. (we have 3)
It is an Adaptec ATA RAID 2400A controller
I'm purchasing a new SCSI drive today. My questions:
... (2 Replies)
Discussion started by: gseyforth
2 Replies
10. Programming
Hi,
I am using gmake to compile a c program with a makefile. The make file runs ld. I get the following error
jsh1035c:/users/egate453/admegate/kapil/samples $ gmake -e -f GNUmakefile queue_c
gmake -f ./GNUmakefile queue_c in_objdir=1 build_root=/users/egate453/admegate/kapil/samples... (2 Replies)
Discussion started by: handak9
2 Replies