10 More Discussions You Might Find Interesting
1. Solaris
TLDR: Patched a separate boot environment to 11.4. Activated and rebooted the system only to have it boot loop and show 11.3 on the patched boot environment.
Bootloop process: The system went down, came up showing 11.3 then spewed bunch of errors and resetted. SEE BELOW FOR THE FINAL MSG... (1 Reply)
Discussion started by: samthewildone
1 Replies
2. Solaris
My system suddenly crash and when it rebooted there was an error:
/dev/rdsk/c1t0d0s3 is logging
svc.startd: svc:/network/nis/client:default: Method "/method/yp" failed with status 96.
The system completes booting however when I log in a user account / directory is not longer... (1 Reply)
Discussion started by: NeedSolarisHelp
1 Replies
3. Solaris
I have an m5000 that Is down.
I have access to XSCF>
and was able to get to the ok prompt.
However, on
>ok boot
it failed to boot.
erred with :
svc.startd: svc:/system/device/fc-fabric:default: Method "/lib/svc/method/fc-fabric" failed due to signal KILL.
Nov 29... (3 Replies)
Discussion started by: goya
3 Replies
4. Solaris
I have a T2000 enterprise SPARC server that's no longer on contract with Oracle. It's on old firmware (6.3.x). After a power-down this weekend, it won't boot normally. Boot snapshot at the bottom of the post.
It can boot to cdrom, and it'll boot to failsafe mode, but it won't do a regular... (9 Replies)
Discussion started by: val riverwalk
9 Replies
5. Solaris
One of our T5220 servers fail to boot due to following error:
ERROR: The following devices are disabled:
XAUI1
XAUI0
I can't see any disabled components in SP console, any idea what is the problem? (1 Reply)
Discussion started by: belalr
1 Replies
6. UNIX for Advanced & Expert Users
Hi,
I am trying to setup a server for a diskless boot of a computer class (with ubuntu)
I followed the guidelines in https://help.ubuntu.com/community/DisklessUbuntuHowto
I have two computers: one is the server I installed and the other is my macbook on which I run a virtual machine... (8 Replies)
Discussion started by: yotamhc
8 Replies
7. Solaris
Hi,
I currently have one BE and would like to create an ABE.
# lustatus
BE_name Complete Active ActiveOnReboot CopyStatus
------------------------------------------------------------------------
coolthreads yes yes yes - But... (3 Replies)
Discussion started by: pgarousi
3 Replies
8. HP-UX
I have a machine running HP-UX 11.23 (PARISC) and APA startup fails on boot. This is found in /etc/rc.log:
Configure Auto-Port Aggregation(LAN Monitor) interfaces
Output from "/sbin/rc2.d/S343hplm start":
----------------------------
get_start_dlpi_version: failed, errno is 22
ERROR: ... (1 Reply)
Discussion started by: kknigga
1 Replies
9. UNIX for Dummies Questions & Answers
Hi, i was installing solaris 8 on sunfire v250 and the power fails :mad: , now it does not boot from cd rom and get the next msg:
ð
Sun Fire V120 (UltraSPARC-IIe 648MHz), No Keyboard
OpenBoot 4.0, 512 MB memory installed, Serial #56338483.
Ethernet address 0:3:ba:5b:a8:33, Host ID: 835ba833.
... (1 Reply)
Discussion started by: agustincm
1 Replies
10. UNIX for Dummies Questions & Answers
During the boot-up process *nix runs scripts linked into the runlevel directories rc#.d. What I'm wondering is, how do I control the environment that those scripts see? I need to set a couple environment variables, and I can NOT do it from within the scripts because it poses a maintenance nightmare... (1 Reply)
Discussion started by: DreamWarrior
1 Replies
sys_attrs_bparm(5) File Formats Manual sys_attrs_bparm(5)
NAME
sys_attrs_bparm - bparm subsystem attributes
DESCRIPTION
This reference page lists and describes attributes for the Boot Parameters (bparm) kernel subsystem. Refer to the sys_attrs(5) reference
page for an introduction to the topic of kernel subsystem attributes.
Identifies the device from which the system was last booted. This attribute corresponds to the console firmware environment vari-
able with the same name. Do not modify this value, which is set when the system boots.
A combination of flags that controls the boot loader and kernel. This attribute corresponds to the console firmware environment
variable with the same name. Values for the variable are: Boot to multiuser mode. By default, the kernel boots to single-user mode.
Enable the kdebug debugger to debug the kernel. By default, kdebug is not enabled in the kernel. Produce full dumps when the system
crashes. By default, partial dumps are produced. Prompt for an alternate kernel and special arguments when the system is booted. By
default, no questions are asked.
Set boot_osflags only at the console prompt or by using the consvar utility.
Identifies the boot device to be used when one is not included in the boot command line. This attribute corresponds to the console
firmware environment variable with the same name. Set bootdef_dev only at the console prompt or by using the consvar utility.
SEE ALSO
Commands: consvar(8)
Others: sys_attrs(5)
System Administration
sys_attrs_bparm(5)