9 More Discussions You Might Find Interesting
1. Solaris
I am trying to connect D1000 storedge with my sun blade 1500 and i am getting the following error when booting the system.
Oct 13 22:21:56 brampton rpcbind: rpcbind terminating on signal.
Oct 13 22:22:02 brampton syseventd: SIGHUP caught - reloading modules
Oct 13 22:22:02 brampton... (9 Replies)
Discussion started by: mnathan
9 Replies
2. Filesystems, Disks and Memory
Alguien me puede ayudar, necesito saber cuantos slot de memoria disponibles tiene un RS/6000 AIX (1 Reply)
Discussion started by: ivan.estay
1 Replies
3. Solaris
Hi,
Recently i was trying to connect Sun Storedge D1000 Array to E420 R (Practice servers). I connected the SCSI cable between array and server. I tried the following :
#devfsadm (nothing showed up)
#format (no new disk is shown here)
i tried this process again after putting ON the... (2 Replies)
Discussion started by: bluegold86
2 Replies
4. Solaris
hi all,
i have a sunfire v440 server , someone can tell me if this server contains a AGP slots ? thanx (4 Replies)
Discussion started by: lid-j-one
4 Replies
5. Solaris
Hello,
I have a d1000, it's connected to two servers, I want both servers to see all disks in the array. i.e. i have 6 disks, 3 in each side, I want both servers to see all 6 disks.
It appears to be setup in a split bus mode now, ive looked thru the manuals and have become confused!
So,... (2 Replies)
Discussion started by: BG_JrAdmin
2 Replies
6. Solaris
Hi everyone,
I have a problem which looks like very simple. My SunFire X4100 have 2 disk slots: HDD0, HDD1 and 1 hard disk. I installed OS on the hard disk at HDD0 and now i want to boot it at HDD1.
When i change BIOS and begin boot at HDD1 it reset after i chose Solaris 10 at OS selecting... (3 Replies)
Discussion started by: tien86
3 Replies
7. Solaris
Hi folks,
I´m having a problem with a Ultra60 box with diff scsi pci card
conected to one D1000. The conection are correct because a checked the
D1000 guide. When a do probe-scsi-all in the OBP, the D1000 blink all
disks one time then the led of one of the disks powers off and then
nothing... (2 Replies)
Discussion started by: spacewalker
2 Replies
8. UNIX for Dummies Questions & Answers
Hi,
im having a problem installing my pci wireless card. Im using knoppix, but my problem is with the mobo i think. im using an older laptop, toshiba satellite 2540 and when i plug in the card i get lights on sometimes. this means its getting power right. so then to install the card into the... (0 Replies)
Discussion started by: jestra
0 Replies
9. UNIX for Advanced & Expert Users
Hi all..
I have a Sun Ultra 450 with a lot of drives and scsi controllers installed and i have one bad internal disk.. How can "map" ex /dev/dsk/c3t2d0s0 to a slot in the internal cabinet? Any good ideas?
I dont want to remove the wrong disk :)
thanks in advance.. (3 Replies)
Discussion started by: s93366
3 Replies
APMLABEL(8) BSD System Manager's Manual APMLABEL(8)
NAME
apmlabel -- update disk label from Apple Partition Map
SYNOPSIS
apmlabel [-fqrw] device
DESCRIPTION
apmlabel is used to update a NetBSD disk label from the Apple Partition Map found on disks that were previously used on Mac OS systems (or
other APM using systems).
apmlabel scans the APM contained in the first blocks of the disk and generates additional partition entries for the disk from the entries
found. Driver and patches partitions are ignored.
Each APM entry which does not have an equivalent partition in the disk label (equivalent in having the same size and offset) is added to the
first free partition slot in the disk label. A free partition slot is defined as one with an fstype of 'unused' and a size of zero ('0').
If there are not enough free slots in the disk label, a warning will be issued.
The raw partition (typically partition c, but d on i386 and some other platforms) is left alone during this process.
By default, the proposed changed disk label will be displayed and no disk label update will occur.
Available options:
-f Force an update, even if there has been no change.
-q Performs operations in a quiet fashion.
-r In conjunction with -w, also update the on-disk label.
-w Update the in-core label if it has been changed.
SEE ALSO
disklabel(8), dkctl(8), pdisk(8)
HISTORY
The apmlabel command appeared in NetBSD 5.0.
BSD
May 19, 2007 BSD