9 More Discussions You Might Find Interesting
1. Solaris
I am trying to connect D1000 storedge with my sun blade 1500 and i am getting the following error when booting the system.
Oct 13 22:21:56 brampton rpcbind: rpcbind terminating on signal.
Oct 13 22:22:02 brampton syseventd: SIGHUP caught - reloading modules
Oct 13 22:22:02 brampton... (9 Replies)
Discussion started by: mnathan
9 Replies
2. Filesystems, Disks and Memory
Alguien me puede ayudar, necesito saber cuantos slot de memoria disponibles tiene un RS/6000 AIX (1 Reply)
Discussion started by: ivan.estay
1 Replies
3. Solaris
Hi,
Recently i was trying to connect Sun Storedge D1000 Array to E420 R (Practice servers). I connected the SCSI cable between array and server. I tried the following :
#devfsadm (nothing showed up)
#format (no new disk is shown here)
i tried this process again after putting ON the... (2 Replies)
Discussion started by: bluegold86
2 Replies
4. Solaris
hi all,
i have a sunfire v440 server , someone can tell me if this server contains a AGP slots ? thanx (4 Replies)
Discussion started by: lid-j-one
4 Replies
5. Solaris
Hello,
I have a d1000, it's connected to two servers, I want both servers to see all disks in the array. i.e. i have 6 disks, 3 in each side, I want both servers to see all 6 disks.
It appears to be setup in a split bus mode now, ive looked thru the manuals and have become confused!
So,... (2 Replies)
Discussion started by: BG_JrAdmin
2 Replies
6. Solaris
Hi everyone,
I have a problem which looks like very simple. My SunFire X4100 have 2 disk slots: HDD0, HDD1 and 1 hard disk. I installed OS on the hard disk at HDD0 and now i want to boot it at HDD1.
When i change BIOS and begin boot at HDD1 it reset after i chose Solaris 10 at OS selecting... (3 Replies)
Discussion started by: tien86
3 Replies
7. Solaris
Hi folks,
I´m having a problem with a Ultra60 box with diff scsi pci card
conected to one D1000. The conection are correct because a checked the
D1000 guide. When a do probe-scsi-all in the OBP, the D1000 blink all
disks one time then the led of one of the disks powers off and then
nothing... (2 Replies)
Discussion started by: spacewalker
2 Replies
8. UNIX for Dummies Questions & Answers
Hi,
im having a problem installing my pci wireless card. Im using knoppix, but my problem is with the mobo i think. im using an older laptop, toshiba satellite 2540 and when i plug in the card i get lights on sometimes. this means its getting power right. so then to install the card into the... (0 Replies)
Discussion started by: jestra
0 Replies
9. UNIX for Advanced & Expert Users
Hi all..
I have a Sun Ultra 450 with a lot of drives and scsi controllers installed and i have one bad internal disk.. How can "map" ex /dev/dsk/c3t2d0s0 to a slot in the internal cabinet? Any good ideas?
I dont want to remove the wrong disk :)
thanks in advance.. (3 Replies)
Discussion started by: s93366
3 Replies
PCI_CREATE_SLOT(9) Hardware Interfaces PCI_CREATE_SLOT(9)
NAME
pci_create_slot - create or increment refcount for physical PCI slot
SYNOPSIS
struct pci_slot * pci_create_slot(struct pci_bus * parent, int slot_nr, const char * name, struct hotplug_slot * hotplug);
ARGUMENTS
parent
struct pci_bus of parent bridge
slot_nr
PCI_SLOT(pci_dev->devfn) or -1 for placeholder
name
user visible string presented in /sys/bus/pci/slots/<name>
hotplug
set if caller is hotplug driver, NULL otherwise
DESCRIPTION
PCI slots have first class attributes such as address, speed, width, and a struct pci_slot is used to manage them. This interface will
either return a new struct pci_slot to the caller, or if the pci_slot already exists, its refcount will be incremented.
Slots are uniquely identified by a pci_bus, slot_nr tuple.
There are known platforms with broken firmware that assign the same name to multiple slots. Workaround these broken platforms by renaming
the slots on behalf of the caller. If firmware assigns name N to
MULTIPLE SLOTS
The first slot is assigned N The second slot is assigned N-1 The third slot is assigned N-2 etc.
PLACEHOLDER SLOTS
In most cases, pci_bus, slot_nr will be sufficient to uniquely identify a slot. There is one notable exception - pSeries (rpaphp), where
the slot_nr cannot be determined until a device is actually inserted into the slot. In this scenario, the caller may pass -1 for slot_nr.
The following semantics are imposed when the caller passes slot_nr == -1. First, we no longer check for an existing struct pci_slot, as
there may be many slots with slot_nr of -1. The other change in semantics is user-visible, which is the 'address' parameter presented in
sysfs will
CONSIST SOLELY OF A DDDD
bb tuple, where dddd is the PCI domain of the struct pci_bus and bb is the bus number. In other words, the devfn of the 'placeholder' slot
will not be displayed.
COPYRIGHT
Kernel Hackers Manual 2.6. July 2010 PCI_CREATE_SLOT(9)