d1000 or minipac with six disk slot

9 More Discussions You Might Find Interesting

1. Solaris

D1000 Storedge array connection

I am trying to connect D1000 storedge with my sun blade 1500 and i am getting the following error when booting the system. Oct 13 22:21:56 brampton rpcbind: rpcbind terminating on signal. Oct 13 22:22:02 brampton syseventd: SIGHUP caught - reloading modules Oct 13 22:22:02 brampton...

2. Filesystems, Disks and Memory

cantidad de slot de memoria

Alguien me puede ayudar, necesito saber cuantos slot de memoria disponibles tiene un RS/6000 AIX

3. Solaris

connection problem with Storedge D1000

Hi, Recently i was trying to connect Sun Storedge D1000 Array to E420 R (Practice servers). I connected the SCSI cable between array and server. I tried the following : #devfsadm (nothing showed up) #format (no new disk is shown here) i tried this process again after putting ON the...

4. Solaris

AGP slot in my server ?

hi all, i have a sunfire v440 server , someone can tell me if this server contains a AGP slots ? thanx

5. Solaris

Storedge D1000 sharing disks between two boxes

Hello, I have a d1000, it's connected to two servers, I want both servers to see all disks in the array. i.e. i have 6 disks, 3 in each side, I want both servers to see all 6 disks. It appears to be setup in a split bus mode now, ive looked thru the manuals and have become confused! So,...

6. Solaris

How to change boot slot X4100?

Hi everyone, I have a problem which looks like very simple. My SunFire X4100 have 2 disk slots: HDD0, HDD1 and 1 hard disk. I installed OS on the hard disk at HDD0 and now i want to boot it at HDD1. When i change BIOS and begin boot at HDD1 it reset after i chose Solaris 10 at OS selecting...

7. Solaris

probe-scsi-all hangs probing D1000

Hi folks, I�m having a problem with a Ultra60 box with diff scsi pci card conected to one D1000. The conection are correct because a checked the D1000 guide. When a do probe-scsi-all in the OBP, the D1000 blink all disks one time then the led of one of the disks powers off and then nothing...

8. UNIX for Dummies Questions & Answers

bad pci slot?

Hi, im having a problem installing my pci wireless card. Im using knoppix, but my problem is with the mobo i think. im using an older laptop, toshiba satellite 2540 and when i plug in the card i get lights on sometimes. this means its getting power right. so then to install the card into the...

9. UNIX for Advanced & Expert Users

device - > slot

Hi all.. I have a Sun Ultra 450 with a lot of drives and scsi controllers installed and i have one bad internal disk.. How can "map" ex /dev/dsk/c3t2d0s0 to a slot in the internal cabinet? Any good ideas? I dont want to remove the wrong disk :) thanks in advance..

LEARN ABOUT NETBSD

apmlabel

APMLABEL(8)						    BSD System Manager's Manual 					       APMLABEL(8)

NAME

     apmlabel -- update disk label from Apple Partition Map

SYNOPSIS

     apmlabel [-fqrw] device

DESCRIPTION

     apmlabel is used to update a NetBSD disk label from the Apple Partition Map found on disks that were previously used on Mac OS systems (or
     other APM using systems).

     apmlabel scans the APM contained in the first blocks of the disk and generates additional partition entries for the disk from the entries
     found.  Driver and patches partitions are ignored.

     Each APM entry which does not have an equivalent partition in the disk label (equivalent in having the same size and offset) is added to the
     first free partition slot in the disk label.  A free partition slot is defined as one with an fstype of 'unused' and a size of zero ('0').
     If there are not enough free slots in the disk label, a warning will be issued.

     The raw partition (typically partition c, but d on i386 and some other platforms) is left alone during this process.

     By default, the proposed changed disk label will be displayed and no disk label update will occur.

     Available options:

     -f  Force an update, even if there has been no change.

     -q  Performs operations in a quiet fashion.

     -r  In conjunction with -w, also update the on-disk label.

     -w  Update the in-core label if it has been changed.

SEE ALSO

     disklabel(8), dkctl(8), pdisk(8)

HISTORY

     The apmlabel command appeared in NetBSD 5.0.

BSD
								   May 19, 2007 							       BSD

UNIX for Advanced & Expert Users