d1000 or minipac with six disk slot

9 More Discussions You Might Find Interesting

1. Solaris

D1000 Storedge array connection

I am trying to connect D1000 storedge with my sun blade 1500 and i am getting the following error when booting the system. Oct 13 22:21:56 brampton rpcbind: rpcbind terminating on signal. Oct 13 22:22:02 brampton syseventd: SIGHUP caught - reloading modules Oct 13 22:22:02 brampton...

2. Filesystems, Disks and Memory

cantidad de slot de memoria

Alguien me puede ayudar, necesito saber cuantos slot de memoria disponibles tiene un RS/6000 AIX

3. Solaris

connection problem with Storedge D1000

Hi, Recently i was trying to connect Sun Storedge D1000 Array to E420 R (Practice servers). I connected the SCSI cable between array and server. I tried the following : #devfsadm (nothing showed up) #format (no new disk is shown here) i tried this process again after putting ON the...

4. Solaris

AGP slot in my server ?

hi all, i have a sunfire v440 server , someone can tell me if this server contains a AGP slots ? thanx

5. Solaris

Storedge D1000 sharing disks between two boxes

Hello, I have a d1000, it's connected to two servers, I want both servers to see all disks in the array. i.e. i have 6 disks, 3 in each side, I want both servers to see all 6 disks. It appears to be setup in a split bus mode now, ive looked thru the manuals and have become confused! So,...

6. Solaris

How to change boot slot X4100?

Hi everyone, I have a problem which looks like very simple. My SunFire X4100 have 2 disk slots: HDD0, HDD1 and 1 hard disk. I installed OS on the hard disk at HDD0 and now i want to boot it at HDD1. When i change BIOS and begin boot at HDD1 it reset after i chose Solaris 10 at OS selecting...

7. Solaris

probe-scsi-all hangs probing D1000

Hi folks, I�m having a problem with a Ultra60 box with diff scsi pci card conected to one D1000. The conection are correct because a checked the D1000 guide. When a do probe-scsi-all in the OBP, the D1000 blink all disks one time then the led of one of the disks powers off and then nothing...

8. UNIX for Dummies Questions & Answers

bad pci slot?

Hi, im having a problem installing my pci wireless card. Im using knoppix, but my problem is with the mobo i think. im using an older laptop, toshiba satellite 2540 and when i plug in the card i get lights on sometimes. this means its getting power right. so then to install the card into the...

9. UNIX for Advanced & Expert Users

device - > slot

Hi all.. I have a Sun Ultra 450 with a lot of drives and scsi controllers installed and i have one bad internal disk.. How can "map" ex /dev/dsk/c3t2d0s0 to a slot in the internal cabinet? Any good ideas? I dont want to remove the wrong disk :) thanks in advance..

LEARN ABOUT OSF1

volrootmir

volrootmir(8)						      System Manager's Manual						     volrootmir(8)

NAME

       volrootmir - Mirror areas necessary for booting to a new disk

SYNOPSIS

       /usr/sbin/volrootmir [-a] [nconfig=count] target_disk [swap=target_partition]

OPTIONS

       Specifies that all volumes on the system disk be mirrored, not just the root and swap volumes, rootvol and swapvol.

DESCRIPTION

       The volrootmir script causes a mirror copy of areas of the root disk involved in booting to be made on the specified target disk.

       When  used without the -a option, volrootmir adds mirrors of the root and swap volumes and allocates them on the new disk. In addition, all
       disk regions required for booting are set up and partitions for the new volume mirrors are created.

       When used with the -a option, volrootmir mirrors all in-use partitions on the system disk.

       To mirror a swap volume that is on a separate disk from the root volume, the swap attribute must be used to specify a separate  target  for
       the swap mirror.

       The  target  disk(s)  must be at least as large as the sum of the sizes of rootvol and swapvol. Also, the physical disk should not have any
       disk partition in use.

       This script can be called from the voldiskadm menus by choosing the Mirror volumes on a disk operation.

ATTRIBUTES

       Specifies the number of log copies and copies of the configuration database, for example,  nconfig=2.   Specifies  that	the  swap  volume,
       swapvol, be mirrored on a separate disk, as specified by target_partition.

EXAMPLES

       The following command mirrors the rootvol and swapvol volumes onto the target disk, dsk3. This command will fail if swapvol is on a differ-
       ent disk from rootvol.

	      # volrootmir dsk3 The following command mirrors rootvol, swapvol, and any other volumes on the root disk onto the target disk, dsk3.
	      This command will fail if swapvol is on a different disk from rootvol.

	      #  volrootmir -a dsk3 The following command mirrors rootvol on disk dsk3, swapvol onto partition dsk7d, and any other volumes on the
	      root disk onto disk dsk3. This command will fail if swapvol is on the same disk as rootvol.

	      # volrootmir -a dsk3 swap=dsk7d The following command mirrors rootvol onto disk dsk3 and swapvol onto partition dsk7d. This  command
	      will fail if swapvol is on the same disk as rootvol.

	      # volrootmir dsk3 swap=dsk7d

SEE ALSO

       volintro(8), voldiskadm(8)

																     volrootmir(8)

UNIX for Advanced & Expert Users