9 More Discussions You Might Find Interesting
1. Solaris
I am trying to connect D1000 storedge with my sun blade 1500 and i am getting the following error when booting the system.
Oct 13 22:21:56 brampton rpcbind: rpcbind terminating on signal.
Oct 13 22:22:02 brampton syseventd: SIGHUP caught - reloading modules
Oct 13 22:22:02 brampton... (9 Replies)
Discussion started by: mnathan
9 Replies
2. Filesystems, Disks and Memory
Alguien me puede ayudar, necesito saber cuantos slot de memoria disponibles tiene un RS/6000 AIX (1 Reply)
Discussion started by: ivan.estay
1 Replies
3. Solaris
Hi,
Recently i was trying to connect Sun Storedge D1000 Array to E420 R (Practice servers). I connected the SCSI cable between array and server. I tried the following :
#devfsadm (nothing showed up)
#format (no new disk is shown here)
i tried this process again after putting ON the... (2 Replies)
Discussion started by: bluegold86
2 Replies
4. Solaris
hi all,
i have a sunfire v440 server , someone can tell me if this server contains a AGP slots ? thanx (4 Replies)
Discussion started by: lid-j-one
4 Replies
5. Solaris
Hello,
I have a d1000, it's connected to two servers, I want both servers to see all disks in the array. i.e. i have 6 disks, 3 in each side, I want both servers to see all 6 disks.
It appears to be setup in a split bus mode now, ive looked thru the manuals and have become confused!
So,... (2 Replies)
Discussion started by: BG_JrAdmin
2 Replies
6. Solaris
Hi everyone,
I have a problem which looks like very simple. My SunFire X4100 have 2 disk slots: HDD0, HDD1 and 1 hard disk. I installed OS on the hard disk at HDD0 and now i want to boot it at HDD1.
When i change BIOS and begin boot at HDD1 it reset after i chose Solaris 10 at OS selecting... (3 Replies)
Discussion started by: tien86
3 Replies
7. Solaris
Hi folks,
I´m having a problem with a Ultra60 box with diff scsi pci card
conected to one D1000. The conection are correct because a checked the
D1000 guide. When a do probe-scsi-all in the OBP, the D1000 blink all
disks one time then the led of one of the disks powers off and then
nothing... (2 Replies)
Discussion started by: spacewalker
2 Replies
8. UNIX for Dummies Questions & Answers
Hi,
im having a problem installing my pci wireless card. Im using knoppix, but my problem is with the mobo i think. im using an older laptop, toshiba satellite 2540 and when i plug in the card i get lights on sometimes. this means its getting power right. so then to install the card into the... (0 Replies)
Discussion started by: jestra
0 Replies
9. UNIX for Advanced & Expert Users
Hi all..
I have a Sun Ultra 450 with a lot of drives and scsi controllers installed and i have one bad internal disk.. How can "map" ex /dev/dsk/c3t2d0s0 to a slot in the internal cabinet? Any good ideas?
I dont want to remove the wrong disk :)
thanks in advance.. (3 Replies)
Discussion started by: s93366
3 Replies
CHARSET(1) Linux User's Manual CHARSET(1)
NAME
charset - Set an ACM for use in one of the G0/G1 charset slots.
SYNOPSIS
charset [-v] G0|G1 [cp437|iso01|vt100|user|<acm_name>]
DESCRIPTION
The linux console has 2 slots for charsets, labeled G0 and G1. charset changes the slot in use by the current VT to either G0 or G1, and
fills the slot either with one of the 3 predefined ACMs (cp437, iso01, vt100) or with a user-defined ACM.
You can ask for the current user-defined ACM by specifying user, or ask a new ACM to be loaded from a file into the user slot, by specify-
ing a filename.
You will note that, although each VT has its own slot settings, there is only one user-defined ACM for all the VTs. That is, whereas you
can have tty1 using G0=cp437 and G1=vt100, at the same time as tty2 using G0=iso01 and G1=iso02 (user-defined), you cannot have at the same
time tty1 using iso02 and tty2 using iso03. This is a limitation of the linux kernel.
Note that you can emulate such a setting using the filterm(1) utility, with your console in UTF8-mode, by telling filterm to translate
screen output on-the-fly to UTF8.
You'll find filterm(1) in the konwert(1) package, by Marcin Kowalczyk, which is available from http://qrczak.home.ml.org/.
OPTIONS
-v be verbose. charset will then print what it does as it does it.
BUGS
charset cannot determine which of the 2 slots is in use at a given time, so you have to tell him which one you want, even if you don't want
to change to the other one. This is a limitation of the console driver.
SEE ALSO
consolechars(8), unicode_start(1), filterm(1).
Console tools 10 Aug 1998 CHARSET(1)