10 More Discussions You Might Find Interesting
1. Solaris
hi there,
i using salaris 10 as my DNS server.
i have 2 dns server primary and secondary. if primary dns server i edit/update, the other secondary dns server must be sync too.
How can i configure if dns server (primary) can sync the secondary? (1 Reply)
Discussion started by: tappetmus
1 Replies
2. AIX
Hi,
In a Dual VIOSs setup having 4 SEA adapters each, how to find which one is Primary and Secondary.?
Regards,
Siva (2 Replies)
Discussion started by: ksgnathan
2 Replies
3. Linux
Hi
New here so forgive my ignorance and inability to express myself in an informative manner ;)
I have a Fedora distribution installed on my development computer. The system we build is meant to run on a slackware dist which is all fine and well. But due to our flow of deployment I would have... (2 Replies)
Discussion started by: inquam
2 Replies
4. Red Hat
Hi,
I have 4 machines and all are NTP configured with same ntp.conf file. But 3 machines are in sync with Time server and 4th machine is not contacting & sync with the NTP server. Please see the below details.
# service ntpd stop
Stopping ntpd: ... (0 Replies)
Discussion started by: uday123
0 Replies
5. Shell Programming and Scripting
Is there a command or better combination of cmds that will give me the list of Unix users in a particular Unix group whether their primary group is that group in question (information stored in /etc/passwd) or they are in a secondary group (information stored in /etc/group).
So far all I got... (5 Replies)
Discussion started by: ckmehta
5 Replies
6. UNIX for Dummies Questions & Answers
Hello All,
Does some one know how to synchronize the primary name server with the secondary without knowing the domains on which synchronization failed.
I have just done /usr/sbin/ndc reload
Alternatively how do i find out the domains on which synchronization failed? (4 Replies)
Discussion started by: a2z1982
4 Replies
7. Filesystems, Disks and Memory
Wellcomes All,
some times ago I 've installed a Debian ditribution on an Hard Disk who was set as Primary Master. Few days ago, I 've decided to install another Hard Disk with a different Operating System. When I did that, I turned off the old hard disk, and I mouted the new one on the Primary IDE... (1 Reply)
Discussion started by: thekarsillo
1 Replies
8. UNIX for Advanced & Expert Users
Hi,
When I invoke a script s1.sh it will call an another script s2.sh by itself. This script s2.sh will call some java files, so while running the script it asks for a file name to be processed. Which we can see in the screen.
The file name to be processed is present in script s1.sh
Now I... (2 Replies)
Discussion started by: venu_eie
2 Replies
9. Shell Programming and Scripting
Hi,
When I invoke a script s1.sh it will call an another script s2.sh by itself. This script s2.sh will call some java files, so while running the script it asks for a file name to be processed. Which we can see in the screen.
The file name to be processed is present in script s1.sh
Now... (1 Reply)
Discussion started by: venu_eie
1 Replies
10. UNIX for Dummies Questions & Answers
Is there any command which can list me all the Group ID's (Primary, Secondary ) assocaited with a single user.
Thanks
Sanjay (2 Replies)
Discussion started by: sanjay92
2 Replies
MIREDO-SERVER.CONF(5) System Manager's Manual MIREDO-SERVER.CONF(5)
NAME
miredo-server.conf - configuration for miredo-server
SYNOPSIS
miredo-server.conf
DESCRIPTON
miredo-server.conf is the configuration file for miredo-server. Each configuration directive consists of one directive name, possibly
followed by one or several spaces and a value for the directive. White spaces, empty lines and lines starting with '#' are ignored.
Directives are case-insensitive. A comprehensive list of the supported directives follows:
SERVER OPTIONS
ServerBindAddress server_ip
Specifies the primary IPv4 address of the Teredo server. miredo-server will bind to UDP/IPv4 port 3544 on this address and waits
for packets from Teredo clients. It will advertise the Teredo prefix which is defined with the Prefix directive.
A Teredo server needs two subsequent IPv4 addresses. It will wait for UDP IPv4 packets on port 3544 on both addresses. server_ip
specifies the lowest of both IPv4 addresses, which is known as the primary IPv4 server address. The secondary IPv4 address should be
server_ip + 1 and must also be assigned to the server.
ServerBindAddress2 server_ip2
It is possible to specify a secondary IPv4 server address manually. However, Miredo clients will need manual configuration (with
the ServerAddress2 directive in miredo.conf). Other Teredo clients are believed not to support such setup.
Prefix teredo_prefix
This directive specifies the Teredo prefix which the Teredo relay and/or server will advertise. teredo_prefix must be a valid IPv6
prefix.
The default value is 2001:0000::. A 32-bits prefix is required to use this option. Since you do not have such big an IPv6 prefix
YOU WILL NOT USE THIS OPTION. Moreover, certain third party Teredo client implementations require the default prefix.
InterfaceMTU mtu
This directive overrides the value of the MTU that is advertised to Teredo clients. The default value is 1280 bytes and should not
be changed if the default Teredo prefix is used.
YOU MUST NOT USE THIS OPTION with the default prefix. This would break interoperability with most Teredo relays.
SyslogFacility facility
Specify which syslog's facility is to be used by miredo-server for logging. Possible values are: daemon (the default), local0, ...
local7, kern and user (see syslog(2)).
SEE ALSO
miredo-server(8)
AUTHOR
Remi Denis-Courmont <remi at remlab dot net>
http://www.remlab.net/miredo/
miredo February 2008 MIREDO-SERVER.CONF(5)