9 More Discussions You Might Find Interesting
1. Red Hat
Hi,
I have two ntp servers in my cluster and I want all the nodes in my cluster to sync with either of the ntp servers or just one. Unfortunately it keep rotating the sync, between my ntp server 1, ntp server 2 and local. Is there anyway I can change the sync to avoid local?
# ntpq -p
... (3 Replies)
Discussion started by: pjeedu2247
3 Replies
2. HP-UX
Hi,
We cant set the listen address of my java process to the IP address or any of the DNS names listen in the hosts file of the server.
We can access the resources of the pid in the web browser through http://<IP / DNS>:port/console
Based on the pid, how can we find what is the listen... (6 Replies)
Discussion started by: mohtashims
6 Replies
3. Solaris
Good morning!
I would like to test a particular port in Solaris, to see if the firewall rules are ok.
Should I install an application, but as yet I have not, have to force solaris to keep an open door, and put any application listening to port 1099, and will test a terminal connectivity via... (5 Replies)
Discussion started by: poyato
5 Replies
4. HP-UX
Hi
I wonder if its possible to setup NTP clients running HP-UX o.s. from a solaris 10 NTP server?
FR (3 Replies)
Discussion started by: fretagi
3 Replies
5. Linux
All here, thank you for listening. Now I've set up a Linux NTP server by adding a external windows NTP server in /etc/ntp.conf. Then I start the ntpd daemon. But how often does the Linux NTP server update its time with the external NTP server? I've looked up everywhere but found no information... (1 Reply)
Discussion started by: MichaelLi
1 Replies
6. SCO
Hi all
I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface?
If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies
7. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
8. UNIX for Dummies Questions & Answers
Hi all,
How can I log all requests on ports for programs like ftp, telnet, rsh, xdmcp etc...
I want to see if anyone uses these programs/protocols and how often.
Is it difficult to setup a log for these ports and listen on all requests?
/combat (4 Replies)
Discussion started by: tonlu
4 Replies
9. Solaris
All,
How do you set a Solaris 9 server which received ntp updates from a ntp server to broadcast them on a local subnet. I have created a /etc/inet/ntp.conf file to receive the updates from a server on network and need to make this server become like a ntp relay from the main server.
Any... (1 Reply)
Discussion started by: bubba112557
1 Replies
NTPD.CONF(5) File Formats Manual NTPD.CONF(5)
NAME
ntpd.conf - Network Time Protocol daemon configuration file
DESCRIPTION
This manual page describes the format of the ntpd(8) configuration file.
The optional weight keyword permits finer control over the relative importance of time sources (servers or sensor devices). Weights are
specified in the range 1 to 10; if no weight is given, the default is 1. A server with a weight of 5, for example, will have five times
more influence on time offset calculation than a server with a weight of 1.
ntpd.conf has the following format:
Empty lines and lines beginning with the `#' character are ignored.
Keywords may be specified multiple times within the configuration file. They are as follows:
listen on address
OpenNTPd has the ability to sync the local clock to remote NTP servers and, if this directive is specified, can act as NTP server
itself, redistributing the local clock.
Specify a local IP address or a hostname the ntpd(8) daemon should listen on to enable remote clients synchronization. If it
appears multiple times, ntpd(8) will listen on each given address. If `*' is given as an address, ntpd(8) will listen on all local
addresses. ntpd(8) does not listen on any address by default. For example:
listen on *
or
listen on 127.0.0.1
listen on ::1
sensor device [correction microseconds] [weight weight-value]
Specify a timedelta sensor device ntpd(8) should use. The sensor can be specified multiple times: ntpd(8) will use each given sen-
sor that actually exists. Non-existent sensors are ignored. If `*' is given as device name, ntpd(8) will use all timedelta sensors
it finds. ntpd(8) does not use any timedelta sensor by default. For example:
sensor *
sensor udcf0
An optional correction in microseconds can be given to compensate for the sensor's offset. The maximum correction is 127 seconds.
For example, if a DCF77 receiver is lagging 15ms behind actual time:
sensor udcf0 correction 15000
server address [weight weight-value]
Specify the IP address or the hostname of an NTP server to synchronize to. If it appears multiple times, ntpd(8) will try to syn-
chronize to all of the servers specified. If a hostname resolves to multiple IPv4 and/or IPv6 addresses, ntpd(8) uses the first
address. If it does not get a reply, ntpd(8) retries with the next address and continues to do so until a working address is found.
For example:
server 10.0.0.2 weight 5
server ntp.example.org weight 1
To provide redundancy, it is good practice to configure multiple servers. In general, best accuracy is obtained by using servers
that have a low network latency.
servers address [weight weight-value]
As with server, specify the IP address or hostname of an NTP server to synchronize to. If it appears multiple times, ntpd(8) will
try to synchronize to all of the servers specified. Should the hostname resolve to multiple IP addresses, ntpd(8) will try to syn-
chronize to all of them. For example:
servers pool.ntp.org
FILES
/etc/openntpd/ntpd.conf
default ntpd(8) configuration file
SEE ALSO
ntpd(8), sysctl(8)
HISTORY
The ntpd.conf file format first appeared in OpenBSD 3.6 .
$Mdocdate: October 2 2007 $ NTPD.CONF(5)