10 More Discussions You Might Find Interesting
1. Red Hat
Thanks for any insights you might have...
I have a RH8 system setup with a DAT drive.
I have a AIX tape that was made using cpio.
Bottom line is I need to read the AIX tape into the RH box.
I was able to do cpio -itv --no-absolute-filenames < /dev/st0 and read the table of contents.
... (0 Replies)
Discussion started by: mike114327
0 Replies
2. UNIX for Dummies Questions & Answers
Hi,
I have a HP SURESTORE 40 tape drive. Several archives are stored on it using DUMP. I have several volumes stored on the tape...
If I issue restore -rf /dev/st0 will it restore just the arhcive that the tape reader is currently on or will it restore all of them?
Thanks, (3 Replies)
Discussion started by: mojoman
3 Replies
3. UNIX for Dummies Questions & Answers
Does anyone know how to read an LTO tape from this jukebox? (3 Replies)
Discussion started by: dr. phreeze
3 Replies
4. SCO
when I do a tape status /dev/rStp0 I get the following on a new tape and I have tried several:
Status : ready beginning-of-tape
soft errors : 0
hard errors: 2
underruns: 5
My BackupEdge has stopped backing up my system because it asks for a new volume yet my total system data is under 20... (5 Replies)
Discussion started by: psytropic
5 Replies
5. UNIX for Dummies Questions & Answers
I've got a backuptape in cpio format that was accidentally overwritten with a very small batch file. As I assume that the cpio header has been overwritten, I cannot extract files from the backup in the conventional manner:
( cpio -itv </dev/rct0
cpio: this is not a cpio file, bad header)
... (0 Replies)
Discussion started by: mart4179
0 Replies
6. AIX
I'm attempting to read a tape in a 4mm drive (AIX 4.3) using the following command...
tar tvf /dev/rmt0
...and I keep getting the following error message:
tar: 0511-193 An error occurred while reading from the media.
There is not enough memory available now.
I've googled this error... (2 Replies)
Discussion started by: tdpearson
2 Replies
7. UNIX for Advanced & Expert Users
Hi,
I' using a sun solaris server, I would like to known if there is the possibility to control how many space is free on a tape and how I can delete a single file on a tape.
Thanks
DOMENICO (3 Replies)
Discussion started by: Minguccio75
3 Replies
8. AIX
I am experimenting with one of my TSM processes, and I am trying to write something to a 4mm tape.
I tried to use the tctl command, but, I was unsuccessful.
what AiX command can I run in order to see if my output is on the tape ?
Thank You ! (0 Replies)
Discussion started by: DATDANGGADUDE
0 Replies
9. UNIX for Dummies Questions & Answers
I have been attempting to read a DLT tape, but encountered problems. I have applied patches from SUN that 'resolve' known problems with tape reading etc...but still the error!
Techsupport reckon that the data/tape is corrupt. I would like to think they aren't.
Are there any issues with... (10 Replies)
Discussion started by: colesy
10 Replies
10. UNIX for Dummies Questions & Answers
Hi all,
I am attempting to read tar images from a DLT tape, and have recieved an error, which i don't know:
tar: blocksize = 8
tar: directory checksum error
I have been able to read from other tapes, using the same command (tar -tvf /devicename) but this time i have an... (3 Replies)
Discussion started by: colesy
3 Replies
st_san_safe(5) OBSOLETED st_san_safe(5)
NAME
st_san_safe - determine whether access to tape device special files without the no-rewind-on-close option is allowed (OBSOLETED)
VALUES
Failsafe
Default
Allowed values
Recommended values
or
DESCRIPTION
Note: this tunable is obsoleted and has been renamed to beginning with release HP-UX 11i v3.
This tunable notifies the tape driver whether it should allow access to device special files without the no-rewind-on-close option. When
this tunable is on the tape driver will fail any open on a tape device special file without the no-rewind-on-close option (that is, or with
a status of
The tunable allows the safe sharing of tape devices in SAN tape backup solution configurations. The disabling of device special files
without no-rewind-on-close in a SAN tape backup solution configuration prevents the accidental sending of a rewind command on close from
HP-UX systems via standard tape commands like which would corrupt a backup in process.
Who Is Expected to Change This Tunable?
Anyone.
Restrictions on Changing
Changes to this tunable take effect immediately.
When Should the Tunable Be Turned On?
This tunable should be turned on if the system is going to be used in a SAN tape backup solution configuration.
What Are the Side Effects of Turning the Tunable On?
The tape driver will fail any open to a tape device special file that does not have the no-rewind-on-close option with a status of This
behavior prevents the usage of any tape device special file without the no-rewind-on-close option.
When Should the Tunable Be Turned Off?
This tunable should be turned off if the system is not part of a SAN tape backup solution configuration or the system utilizes will not
function unless it has access to device special files without the no-rewind-on-close option.
What Are the Side Effects of Turning the Tunable Off?
A rewind may be issued from this system accidentally on close possibly corrupting a backup being issued from another system on the SAN.
What Other Tunables Should Be Changed at the Same Time?
None.
WARNINGS
All HP-UX kernel tunable parameters are release specific. This parameter may be removed or have its meaning changed in future releases of
HP-UX.
Installation of optional kernel software, from HP or other vendors, may cause changes to tunable parameter values. After installation,
some tunable parameters may no longer be at the default or recommended values. For information about the effects of installation on tun-
able values, consult the documentation for the kernel software being installed. For information about optional kernel software that was
factory installed on your system, see at
AUTHOR
was developed by Hewlett-Packard.
SEE ALSO
norewind_close_disabled(5), scsi_tape(7), scsimgr_estape(7).
Tunable Kernel Parameters st_san_safe(5)