While rebooting one of the UNIX systems here at work, the boot-up process halted and a message appeared telling me that I had to run the fsck command. The command to the best of my knowledge went something like :
Code:
fsck -F ufs /dev/rdsk/c0t0d0s0
Can someone give me a full list of this command actually looks at and repairs. Is it just the blocks that it repairs or is it i-node values aswell??
Any information here would be most helpful!
Last edited by Yogesh Sawant; 04-10-2011 at 11:09 AM..
Reason: added code tags
it checks inodes as well as other file-system structure details. I do not believe it does a physical scan (i.e. bad blocks), although that may depend on your particular OS version. At least under linux there is a separate tool for this (which can be called by fsck if you pass a certain flag)
man fsck
fsck(1M) fsck(1M)
NAME
fsck (generic) - file system consistency check and interactive repair
SYNOPSIS
/usr/sbin/fsck [-F FSType] [-m] [-V] [special ...]
/usr/sbin/fsck [-F FSType] [-o FSspecific-options] [-V] [special ...]
DESCRIPTION
The fsck command audits and interactively repairs inconsistent
conditions for HP-UX file systems on mass storage device files
identified by special. If the file system is consistent, the number of files on that file system and the number of used and free blocks are reported. If the file system is inconsistent, fsck provides a mechanism to fix these inconsistencies, depending on which form of the fsck command is used.
special represents a special device (e.g., /dev/rdsk/c1d0s8).
Options
fsck recognizes the following options:
-F FStype Specify the file system type on which to operate
(see fstyp(1M) and fs_wrapper(5)). If this option
is not included on the command line, then the file
system type is determined from the file /etc/fstab
by matching special with an entry in that file.
If there is no entry in /etc/fstab, then the file
system type is determined from the file
/etc/default/fs.
-m Perform a sanity check only. fsck will return 0
if the file system is suitable for mounting. If
the file system needs additional checking, the
return code is 32. If the file system is mounted,
the return code is 33. Error codes larger than 33
indicate that the file system is badly damaged.
-o FSspecific-options
Specify options specific to each file system type.
FSspecific-options is a list of suboptions and/or
keyword/attribute pairs intended for a file-
system-specific version of the command. See the
file-system-specific manual entries for a
description of the specific_options supported, if
any.
-V Echo the completed command line, but perform no other action. The command line is generated by incorporating the user-specified options and other information derived from /etc/fstab. This option allows the user to verify the command line.
RETURN VALUES
The following values are returned by the -m option to fsck:
0 Either no errors were detected or all errors were corrected.
32 The file system needs additional checking.
33 The file system is mounted.
Return values greater that 33 indicate that file system is badly
corrupted. File system specific versions of fsck will have their own
additional return values (see fsck_FSType(1M)).
WARNINGS
This command may not be supported for all file system types.
FILES
/etc/default/fs Specifies the default file system type
/etc/fstab Default list of file systems to check
STANDARDS CONFORMANCE
fsck: SVID3
SEE ALSO
fsck_FSType(1M), mkfs(1M), newfs(1M), fstab(4), fs_wrapper(5).
Last edited by Yogesh Sawant; 04-10-2011 at 11:11 AM..
Reason: added code tags
One other thing to rememebr about fsck (at least under Solaris) is that it's primary function is to maintain the integrity of the file system, not the data in the file system. Complete files that are "misplaced" will be put in lost+found, but partial files will be dropped.
Hi,
I have Solaris-10 OS on T5220. Both local disks were mirrored under SVM. Somehow when one disk gone bad (c0t1d0), other disk (c0t0d0) also got lot of bad block. We have readable data only on c0t0d0, but as soon as server comes after, it hangs when I run few commands because of read errors,... (1 Reply)
Dear all,
I want to execute fsck command,can i execute fsck command without any option
asking for more confidence.
Thanks and Regards
Monoj Das (1 Reply)
What can I fix this issue? I have ran below commands but everything is same.:confused:
WARNING: Last shutdown is later than time on time-of-day chip: check date.
The / file system (/dev/rdsk/c1t0d0s0) is being checked
WARNING - unable to repair the / filesystem. Run fsck manually (fsck -F... (4 Replies)
I am using Mac OS X and my server keeps crashing every several hours or so. I have checked the log file at /var/log/system.log and the entries closest to the crash read
Mar 15 22:27:23 server servermgrd: servermgr_dns: no name available via DNS for 192.168.84.21
Mar 15 22:27:23 server... (4 Replies)
Dear all
I am new for HP-UX.
I have HP rp2470 running HP-UX 10.x
When i run fsck in a root, the output is as below:
#:root> fsck
fsck: /dev/vg00/rlvol1: mounted file system
continue (y/n)? y
** /dev/vg00/rlvol1
** Last Mounted on /stand
** Phase 1 - Check Blocks and Sizes
** Phase... (3 Replies)
I am having a problem with fsck. I am new to UNIX but was placed in a position where I must learn it. Anyway, one of the instructions that I have been given is to use 'fsck -f -y' when I am having trouble with the filesystem. The problem is that I am getting an error message that says the -f... (1 Reply)