10 More Discussions You Might Find Interesting
1. UNIX for Beginners Questions & Answers
Greeting All
Diag tool HDD clone SCO 5 + Oracle 7 DB ( IBM T30 )
I am new to this forum and my knowledge on computers OS is average .
I have just acquired a factory diag tool for BMW/RR/MINI from a retired mechanic. Its runs on a IBM T30 laptop with a Unix/Oracle DB system. Sco 5... (8 Replies)
Discussion started by: bmw635
8 Replies
2. SCO
Hi all
I have read about mounting crashed HDD from a sco system in this forum. However this I received an image on raw format of the crashed system that was using an IDE HDD. Which method should I mount my image? IDE scsi or USB? The image is stores in an external connected through USB .
Also... (4 Replies)
Discussion started by: OrangeKenny
4 Replies
3. Solaris
Dear All,
I have been trying to move my existing Solaris Installation (x86, 10/08) to a bigger HDD.
So I created a 22 cylinder boot partition and used the rest of the space for a Solaris2 partition. Then I created slices same size like on my current disk.
I copied all files with cpio and... (3 Replies)
Discussion started by: BigT79
3 Replies
4. Solaris
I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies
5. Solaris
All,
I am a complete grasshopper when it comes to Unix, so here goes. I have a Solaris 9 server, running two 36GB HDD in a mirrored configuration. I am running low on disk space, and have purchased an additional 145GB HDD. Can anyone point me in the direction to some documentation on how to... (1 Reply)
Discussion started by: ptvenom427
1 Replies
6. SCO
Hi guys,
I have this problem ,
One of our client's hdd went down and we cannot boot up the machine , I've installed a new hdd with a fresh copy of SCO 5.0.6 same as the one in the old HDD, i think the data still good in the old HDD.
My question!!!
How can i access the data from the fresh... (4 Replies)
Discussion started by: josramon
4 Replies
7. UNIX for Dummies Questions & Answers
Hi All,
I need some advice on dual booting a dell box so that I can have WinXP and Solaris 10 OS there. The question is, what is the best way of preparing the hdd for prior to installation?
I have used created two partition, one for xp and the and the other unallocated partition for Solaris.... (3 Replies)
Discussion started by: S0laris_B0y
3 Replies
8. SCO
Hi guys,
I have this quick question , is it posible to isntall SCO 5.0.7 on a serial ATA and if it is can you tell me how or maybe a website that has some info about this.
I'm not using any raid, just one HDD.
Thanks a lot (0 Replies)
Discussion started by: josramon
0 Replies
9. Shell Programming and Scripting
Hi Engg. ! :mad:
I have a harddisk on which SCO UNIX Open Server was installed. There was some data (in .dbf format) on it. Present condition of HDD is that it is not booting. Now I want to mount this HDD through other HDD on which SCO UNIX Open Server is installed by attaching... (0 Replies)
Discussion started by: Niraj Gopal Sha
0 Replies
10. UNIX for Advanced & Expert Users
HI ALL,
I need to backup HDD with SCO UNIX. I need to have a full functionaly backup of this hard disk. Does anybody have any tool or subsription how to do it. I tried some SW, but after when I tried to use this copy of my original disk "can not find a root directory". Thanks in advance. (1 Reply)
Discussion started by: jardas
1 Replies
EDAC-CTL(8) EDAC admin utility EDAC-CTL(8)
NAME
edac-ctl - EDAC admin utility
SYNOPSIS
edac-ctl [OPTION]...
DESCRIPTION
The edac-ctl program is a perl(1) script which performs some useful administration tasks for EDAC (Error Detection and Correction) drivers.
OPTIONS
--help Display a brief usage message.
--mainboard
Print mainboard vendor and model for this hardware, if available. The method used by edac-ctl to obtain the mainboard vendor and
model information for the current system is described below in the MAINBOARD CONFIGURATION section.
--status
Print the status of EDAC drivers (loaded or unloaded).
--register-labels
Register motherboard DIMM labels into EDAC driver sysfs files. This option uses the detected mainboard manufacturer and model num-
ber in combination with a "labels database" found in any of the files under /etc/edac/labels.d/* or in the labels.db file at
/etc/edac/labels.db. An entry for the current hardware must exist in the labels database for this option to do anything.
--print-labels
Display the configured labels for the current hardware, as well as the current labels registered with EDAC.
--labeldb=DB
Specify an alternate location for the labels database.
MAINBOARD CONFIGURATION
The edac-ctl script uses the following method to determine the current system's mainboard vendor and model information:
1. If the config file /etc/edac/mainboard exists, then it is parsed by edac-ctl. The mainboard config file has the following simple syn-
tax:
vendor = <mainboard vendor string>
model = <mainboard model string>
script = <script to gather mainboard information>
Where anything after a '#' character on a line is considered a comment. If the keyword script is specified, then that script or exe-
cutable is run by edac-ctl to gather the mainboard vendor and model information. The script should write the resulting information on
stdout in the same format as the mainboard config file.
2. If no mainboard config file exists, then edac-ctl will attempt to read DMI information from the sysfs files
/sys/class/dmi/id/board_vendor
/sys/class/dmi/id/board_name
3. If the sysfs files above do not exist, then edac-ctl will fall back to parsing output of the dmidecode(8) utility. Use of this utility
will most often require that edac-ctl be run as root.
SEE ALSO
edac(3), edac-util(1)
edac-utils-0.18-1 2011-11-09 EDAC-CTL(8)
SCO 5.0.5 installation on 80GB HDD