10 More Discussions You Might Find Interesting
1. Solaris
Hi Everyone,
In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
2. UNIX for Dummies Questions & Answers
Hi,
I am trying to add a parallel printer to my SCO OSR6 server, yet when I run mkdev parallel it just brings up the message: "Parallel Ports are configured automatically in SCO Openserver 6".
So when I try and add a local printer, no /dev/lp# ports are shown in the list, only serial ports... (1 Reply)
Discussion started by: Martyn
1 Replies
3. SCO
I'm floundering here trying to locate a PCI-E 1x HBA that will support an external tape drive in SCO Openserver 6. I was unable to find anything that would work in the compatible hardware list and a call to Adaptec confirmed that PCI-X would've been a better option for the risers in the Dell 2950... (1 Reply)
Discussion started by: s_mal
1 Replies
4. SCO
How do or what do I need to add PCI / PCIe (PCI Express) parallel ports add-on adapters to OpenServer 6.0.0? OpenServer 5 could see PCI slots but OpenServer 6.0.0 (Original CD or the Re-cut one) required a maintenance pack to be installed? Is this right and how do I check to see if these work? (2 Replies)
Discussion started by: uxlunatick
2 Replies
5. SCO
I need SCO Openserver 4.2. Please, give me distributive of that version SCO:eek: (0 Replies)
Discussion started by: caine
0 Replies
6. UNIX for Dummies Questions & Answers
I am having issues with SCO recognizing my parallel port. The port is being used so I can run dialogic using a dongle for the serial number but the port is not noticed. It is turned on in the bios and should work fine but when I attempt to run the software I get errno=6 and it appears to not be... (0 Replies)
Discussion started by: shuhemizer
0 Replies
7. UNIX for Dummies Questions & Answers
Hi guys,
I just got this new 6.0 version and i'm trying to setup a remote office to telnet to this server running sco 6.0, in previous version all i have to do is add this file under /etc/rc2.d call S99route and put the gate in that file and that was it, for some reason in 6.0 it does not... (1 Reply)
Discussion started by: josramon
1 Replies
8. Filesystems, Disks and Memory
is there a command so that i can se info about the parallel port, if there isn't a specific command for that is there a command so i can se info about the system and all ports and devices?
Thanx
/Nick (2 Replies)
Discussion started by: sajjan2
2 Replies
9. UNIX for Dummies Questions & Answers
hello!
when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ?
kindly help me
thanks (1 Reply)
Discussion started by: buntty
1 Replies
10. UNIX for Dummies Questions & Answers
I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work
i need to change the mouse configuration, ... (2 Replies)
Discussion started by: jimmyvaldes
2 Replies
PARPORT_REGISTER_POR(9) Parallel Port Devices PARPORT_REGISTER_POR(9)
NAME
parport_register_port - register a parallel port
SYNOPSIS
struct parport * parport_register_port(unsigned long base, int irq, int dma, struct parport_operations * ops);
ARGUMENTS
base
base I/O address
irq
IRQ line
dma
DMA channel
ops
pointer to the port driver's port operations structure
DESCRIPTION
When a parallel port (lowlevel) driver finds a port that should be made available to parallel port device drivers, it should call
parport_register_port. The base, irq, and dma parameters are for the convenience of port drivers, and for ports where they aren't
meaningful needn't be set to anything special. They can be altered afterwards by adjusting the relevant members of the parport structure
that is returned and represents the port. They should not be tampered with after calling parport_announce_port, however.
If there are parallel port device drivers in the system that have registered themselves using parport_register_driver, they are not told
about the port at this time; that is done by parport_announce_port.
The ops structure is allocated by the caller, and must not be deallocated before calling parport_remove_port.
If there is no memory to allocate a new parport structure, this function will return NULL.
COPYRIGHT
Kernel Hackers Manual 3.10 June 2014 PARPORT_REGISTER_POR(9)