100Mb/s full duplex link

10 More Discussions You Might Find Interesting

1. Programming

C++/Java full-duplex communication

Hello, here's my situation: I have a C++ server running on a well known machine and a number of Java clients running on other machines (assumed as unknown) on the same LAN. What I want to achieve is full duplex communication between those applications, in order to exchange complex objects and data...

2. Solaris

How to find half duplex or full duplex

Hi, How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct? Also let me know how to change from half to full duplex.

3. UNIX for Advanced & Expert Users

How to set full duplex for solaris 5.5

I would like to change half duplex to full duplex on solaris 5.5. I tried with below commands but they didnt work on solaris 5.5. #ndd -set /dev/le adv_100fdx_cap 1

4. SuSE

configure full duplex

How do I configure full duplex on suse 8.2 I tried ethtool -s eth0 speed 100 duplex full autoneg off the above works but when I reboot the machine the configure was lost. How do I configure full duplex so that when the machine get rebooted the configuration will stay. My interface...

5. Solaris

How to force a full duplex

I need to change some Ip addresses for my servers to reflect in the NIS map. I also need to force full duplex on the 10/100 cards & 1/2 duplex in the 10 cards. I can change the IP by doing ifconfig <NIC card > plumb up <newip>. Not quite sure on how to force the full / half duplex & how to...

6. Programming

full -duplex ?

what is meant by full duplex and half duplex? b'coz in differences b\w hub and switch ,i heard lot this duplex word so please help me

7. UNIX for Dummies Questions & Answers

Full Duplex Howto

Dear Members, I was reading a few posts and saw something about installing two Nics so one could use Full Duplex. I remember back in the day of dial up, you could have two modems and use one for upstream and one for downstream. This was called shotgunning. It seems that you can now do the same...

8. UNIX for Dummies Questions & Answers

Full duplex at HUB?

Ok at the moment I have a hub whit 5 computers connected to it. It's a 10/100 NetGear hub. Ok I heard that there is some command I can run or a file I edit or something like that. But what the command/file/script/whatever does is tells you what connect speed it's connecting to the hub to. ...

9. UNIX for Dummies Questions & Answers

How to configure Full Duplex and TCP/IP

We are using ZIX 4.3.3 and we need to configure the NIC for ful duplexing and we also need to configure it for a TCP/IP default gateway and DNS server to acccess the Interent. Can you please tell me the commands and procedures for configuring this? Thanks Marc

10. IP Networking

Problems switching to Full Duplex

We run Compaq UNIX Tru64 5.1. After a switch got replaced our ethernet-card was magically set to half duplex! We saw, that the card was set to Autonegotiate: vmunix: ee1: Autonegotiated, 100 Mbps full duplex So we set the card with ifconfig to 100 Mbps full duplex with the following...

LEARN ABOUT DEBIAN

ex

EX(4)							 BSD/i386 Kernel Interfaces Manual						     EX(4)

NAME

     ex -- Ethernet device driver for the Intel EtherExpress Pro/10 and Pro/10+

SYNOPSIS

     To compile this driver into the kernel, place the following line in your kernel configuration file:

	   device ex

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

	   if_ex_load="YES"

DESCRIPTION

     The ex driver provides support for Ethernet adapters based on the Intel i82595 chip.

     On the ISA bus, the card will be searched for in the I/O address range 0x200 - 0x3a0.  The IRQ will be read from the EEPROM on the card.  For
     correct operation Plug-N-Play support should be disabled.

     On the PC Card bus, the card will be automatically recognized and configured.

HARDWARE

     The ex driver supports the following Ethernet adapters:

     o	 Intel EtherExpress Pro/10 ISA
     o	 Intel EtherExpress Pro/10+ ISA
     o	 Olicom OC2220 Ethernet PC Card
     o	 Olicom OC2232 Ethernet/Modem PC Card
     o	 Silicom Ethernet LAN PC Card
     o	 Silicom EtherSerial LAN PC Card

DIAGNOSTICS

     ex%d: Intel EtherExpress Pro/10, address %6D, connector %s  The device probe found an installed card, and was able to correctly install the
     device driver.

     ex%d: WARNING: board's EEPROM is configured for IRQ %d, using %d  The device probe detected that the board is configured for a different
     interrupt than the one specified in the kernel configuration file.

     ex%d: invalid IRQ.  The device probe detected an invalid IRQ setting.

SEE ALSO

     arp(4), netintro(4), ng_ether(4), ifconfig(8)

HISTORY

     The ex device driver first appeared in FreeBSD 2.2.

AUTHORS

     The ex device driver was written by Javier Martin Rueda.  The PC Card attachment was written by Mitsuru ISAWAKI and Warner Losh.  This manual
     page was written by David E. O'Brien.

BUGS

     Currently the driver does not support multicast.

     The Silicom EtherSerial card's serial port does not currently work.  The Olicom OC2232 PC Card should work with the ex driver, but is cur-
     rently completely broken.

BSD
								   July 16, 2005							       BSD

UNIX for Advanced & Expert Users