10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
2. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
3. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
4. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
7. Solaris
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies
8. UNIX for Dummies Questions & Answers
My system info is show below:-
#uname -a
SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500
and I have two network card as shown below:-
#ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies
9. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
10. Solaris
Hi guys,
Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot).
I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies