8 More Discussions You Might Find Interesting
1. AIX
Hi,
This is follow up to the post https://www.unix.com/aix/233361-san-disk-appearing-double-aix.html
When I connected Pseries Machine HBA Card ( Dual Port ) directly to the SAN Storage DS4300 , I was able to see Host Port Adapter WWN numbers , although I was getting this message... (2 Replies)
Discussion started by: filosophizer
2 Replies
2. AIX
Hello everyone
I would like to hear your opinions about Aix 6.1 and Aix 5.3 with Storage Hitachi the model is USP VM.
We buy it and I want to know day to day task with this storage and Aix.
Thanks for your comments.
Best wishes for this 2010 (2 Replies)
Discussion started by: lo-lp-kl
2 Replies
3. AIX
Host Name - xxxxxxx
IP Address - xxxxxxxxx
Alert Msg - The percentage of available storage space (DMXMemory) is low (49.54374442289481 percent).
Time received - 14:23
Time Logged - 14:55
Suggested Group - MR-UNIX (5 Replies)
Discussion started by: Nyiko
5 Replies
4. AIX
Hi Guys,
It's me again with this unending support of AIX43 ML 9.
I finally able to test a migration from SSA to SAN, no problem. One problem, I bought some expansion of DS4300, two arrays. The IBM tech told me that before I can connect to the existing DS4300, I need to upgrade the firmware... (1 Reply)
Discussion started by: itik
1 Replies
5. AIX
hi,
i'm new to this company and i'm using old AIX 4.3 with DAS and SSA storage. What is the best way to query a report for disk capacity, usage, free, etc.
I know in AIX 5 there's a command for "du -g /" or "du -m /" to report the total usage but I'm not using AIX5. In AIX 4.3 I can use "df... (5 Replies)
Discussion started by: venerayan
5 Replies
6. AIX
Hi,
How do I query for unused partition in AIX 4.3 with DAS and SAA storage?
I know most unix administrator don't put all the capacity on the system at once.
thanks,
vene (1 Reply)
Discussion started by: venerayan
1 Replies
7. AIX
Hi:-
What is the best way to determine what type of storage is attached to an AIX server?
Thanks, (2 Replies)
Discussion started by: janet
2 Replies
8. Filesystems, Disks and Memory
Hello,
We're setting up a solution for a group of customers with 2 p520 servers and 1 DS4300 unit with 9 disks (at this stage). The meaning is to create two arrays on the DS4300. Both servers will be connected to the DS4300 unit and to both controllers (e.g. Controller 1 connected to server 1... (0 Replies)
Discussion started by: EricBE
0 Replies
KUMOCTL(1) General Commands Manual KUMOCTL(1)
NAME
kumoctl - show kumofs status
SYNOPSIS
kumoctl address[:port=19750] command [options]
DESCRIPTION
Show status of kumo-manager and send control commands to kumo-manager.
COMMANDS
status show status of the cluster
attach attach all new servers and start replace
attach-noreplace
attach all new servers
detach detach all fault servers and start replace
detach-noreplace
detach all fault servers
replace
start replace without attach/detach
full-replace
start full-replace (repair consistency)
backup [suffix=20090304]
create backup with specified suffix
enable-auto-replace
enable auto replace
disable-auto-replace
disable auto replace
STATUS
hash space timestamp
The time that the list of attached kumo-servers is updated. It is updated when new kumo-server is added or existing kumo-server is
down.
attached node
The list of attached kumo-servers. (active) is normal node and (fault) is fault node or recoverd but not re-attached node.
not attached node
The list of recognized but not-attached nodes.
AUTO REPLACING
By default, you have to attach new kumo-servers manually using kumoctl command. If the auto replacing is enabled, new kumo-servers are
attached automatically. This is experimental feature.
EXAMPLE
$ kumoctl mgr1 status
$ kumoctl mgr1 attach
SEE ALSO
kumo-manager(1).
kumoctl July 2009 KUMOCTL(1)
