10 More Discussions You Might Find Interesting
1. SCO
Hello all,
First off- great forum! I have learned a lot just by reading some of the questions and answers. Good to see there are good people out there still willing to help!
Here is my dilemma- I have a fairly new server running an Activant product on it, which runs SCO openserver 5.0.5... (9 Replies)
Discussion started by: crt001
9 Replies
2. UNIX for Advanced & Expert Users
Hi All ,
I wanted to install SCO Open server 5.0.7 on HP DC7600 Desktop Machine, is there any bootloader and which site i can find it to enable me install it because the system is not recognizing the Hard disk just like the ML G Series machine installations.
Please help if you have done this... (4 Replies)
Discussion started by: davosky
4 Replies
3. SCO
hello, i want to install release 5.0.5 on my notebook but the system hangs when extracing files from source media in fact after configuration all of setting please help me:confused: (1 Reply)
Discussion started by: hossein
1 Replies
4. SCO
can not for the life of me workout which BTLD to load allways shows no HDD available can any one give me a clue
tried
hpsas
aacraid
lsil
a160
a320
server is a ML310 G4 ?????:confused::confused: (7 Replies)
Discussion started by: wildginger
7 Replies
5. SCO
I'm trying to install openserver 6.0 on a locally assembled ACPI Multiprocessor PC with an intel core 2 dou e4400 @ 2 ghx and a WD8000JD SATA HD. Immediately after the startup screen I get "PANIC: kernel-mode address fault on kernel address 0xf000ff53". I get this message even if the drive is... (1 Reply)
Discussion started by: tvmccorm
1 Replies
6. SCO
we are installing Openserver 5.0.7, system have SAS controller (Hard Disk Attached) as well as Adaptec ultra 320 controller (Tape Drive Attached).
At the time of installation we link both driver BTLD
Boot: Defbootstr link=accraid ad320
Aftes succesfully installation of accraid btld... (6 Replies)
Discussion started by: hafizurr
6 Replies
7. SCO
Hello!
I made a try to install SCO OS 6.0 on Fujitsu-Siemens L200 server. The installation hangs on the logo screen after the very fast rotating of the small circles. On another simple PC everything went OK. Any idias will be greatly appreciated. (0 Replies)
Discussion started by: olht
0 Replies
8. SCO
Hi everyone,
We r installing sco openserver 5.07 on dell poweredge 2800 but we are facing problem when installing SCSI-raid drivers. Dell provide Perc4 raid card and we dont found raid drivers for this specific raid card. So we r stuck up on primary stage and we also dont know the... (2 Replies)
Discussion started by: mineshkoli
2 Replies
9. Solaris
hello solaris friends,
I've tried installing Sun Solaris 10.0, but everytime it seems to bypass the network config. screen that looks similar to this...here's the url:
http://www.hup.hu/old/images/hup/Solaris/Sol10beta7/9.png
I'm able to install it all the way through but I get no... (2 Replies)
Discussion started by: cadmiumgreen
2 Replies
10. IP Networking
I have certain problems while Installing UNIX OPENSERVER.Could anyone solve that if I provide that problem. (3 Replies)
Discussion started by: Rajraius
3 Replies
MKFS.BFS(8) System Administration MKFS.BFS(8)
NAME
mkfs.bfs - make an SCO bfs filesystem
SYNOPSIS
mkfs.bfs [options] device [block-count]
DESCRIPTION
mkfs.bfs creates an SCO bfs filesystem on a block device (usually a disk partition or a file accessed via the loop device).
The block-count parameter is the desired size of the filesystem, in blocks. If nothing is specified, the entire partition will be used.
OPTIONS
-N, --inodes number
Specify the desired number of inodes (at most 512). If nothing is specified, some default number in the range 48-512 is picked
depending on the size of the partition.
-V, --vname label
Specify the volume label. I have no idea if/where this is used.
-F, --fname name
Specify the filesystem name. I have no idea if/where this is used.
-v, --verbose
Explain what is being done.
-c This option is silently ignored.
-l This option is silently ignored.
-h, --help
Display help text and exit.
-V, --version
Display version information and exit. Option -V only works as --version when it is the only option.
EXIT CODES
The exit code returned by mkfs.bfs is 0 when all went well, and 1 when something went wrong.
SEE ALSO
mkfs(8)
AVAILABILITY
The mkfs.bfs command is part of the util-linux package and is available from https://www.kernel.org/pub/linux/utils/util-linux/.
util-linux July 2011 MKFS.BFS(8)