10 More Discussions You Might Find Interesting
1. Solaris
Hi all
I have a DLT tape in that tape backup is there is in veritas volume format and i want to restore it in ufs file system how can i do it?
right now i don't have veritas file system setup. i have only ufs file sysytem
please help some production data is to be restore.
backup was taken... (0 Replies)
Discussion started by: nikhil kasar
0 Replies
2. Solaris
hi all
i have a DLT tape in that tape backup is there is in veritas volume format and i want to restore it in ufs file system how can i do it?
right now i don't have veritas file system setup. i have only ufs file sysytem
please help some production data is to be restore. (3 Replies)
Discussion started by: nikhil kasar
3 Replies
3. UNIX for Advanced & Expert Users
Hello,
Usually I use "vxresize" to grow vxfs directory in a stand-alone server without any problems, but I am just told to grow vxfs directorys in Veritas Cluster nodes.
Since I never done it before, would like to ask all the experts here to make sure the concept and steps will be fine... (1 Reply)
Discussion started by: sunnychen98
1 Replies
4. Solaris
Hi All,
I have rootdg encapsulated within Veritas Volume Manager.
/# vxprint -vg rootdg
TY NAME ASSOC KSTATE LENGTH PLOFFS STATE TUTIL0 PUTIL0
v rootvol root ENABLED 24585216 - ACTIVE - -
v swapvol swap ENABLED 20484288 -... (3 Replies)
Discussion started by: solaris_1977
3 Replies
5. Solaris
Hi all,
How to i use vxfs for my server? Because when i install OS, it is installed with ufs, then after Solaris 10 installation, i proceed to install vxfs.
How do i convert all the ufs to vxfs? Or is it what i'm doing is the incorrect way?
Please help. :wall: (9 Replies)
Discussion started by: beginningDBA
9 Replies
6. Solaris
Hi,
I have 2 hosts with Veritas VxVM and VxFS (5.0 MP3_RP2). I need to use the application filesystem's luns from these 2 hosts and mount it on another 2 hosts that are running Solaris 9 09/05 and SVM.
Is there resources online or has someone tried this? (4 Replies)
Discussion started by: xor
4 Replies
7. Solaris
what is the difference between VXVM and SVM ?
What is the advantages of VXVM over SVM ?
thanks (2 Replies)
Discussion started by: sijocg
2 Replies
8. Solaris
How to find & replace bad disks in solaris & VXVM?plz
explain step by step? (2 Replies)
Discussion started by: xtreams
2 Replies
9. Solaris
hi guys,
I am studying for the solaris scsa and i want to practice with ufsdump and restores, fssnaps etc...
my question is, i finally found a server with a tape drive attached that i can mess arouund with because its not a critical box.
its running solaris 8, and i want to do a ufsdump, but... (2 Replies)
Discussion started by: BG_JrAdmin
2 Replies
10. UNIX for Advanced & Expert Users
Hello ! :confused:
Does anyone knows anything about procedure to convert Solaris UFS filesystem to VxFS.
Thx,
Witt (1 Reply)
Discussion started by: witt
1 Replies
pfto(7) Miscellaneous Information Manual pfto(7)
NAME
pfto - Powerfail Timeout
DESCRIPTION
HP-UX SCSI disk device drivers have a timeout facility that detects non-responding disks. VxVM uses this mechanism in its Powerfail Time-
out (pfto) feature. You can specify a timeout value for individual VxVM disks using the vxdisk command (see the EXAMPLES section below).
If a disk fails to respond in the specified timeout period, the driver receives a timer interrupt.
pfto values are persistent across reboots, that is, after the pfto value is set, it remains in effect until you explicitly change it. If
dynamic multipathing is enabled, the pfto value set on a disk applies to each path of a multipath disk device.
The pfto value is in seconds. If pfto is not specified, or is zero, the timeout period is 30 seconds. Both the vxdisk and vxprint commands
display the current pfto value for a disk.
EXAMPLES
Use the following command to set the value of pfto to 30 seconds on disk01:
vxdisk -g rootdg set disk01 pfto=30
Use either of the following commands to display the pfto value on the VxVM disk disk01:
vxdisk list disk01
vxprint -l disk01
EXIT CODES
Setting the pfto value on a non-VxVM disk returns an error.
SEE ALSO
vxdisk(1M), vxprint(1M)
VxVM 5.0.31.1 24 Mar 2008 pfto(7)