Hello.
I have a server RS/6000 with AIX 4.2. The server have a network card with 10/100mbps speed, but for some reason, the ethernet only runs at 10Mbps, it doesn,t matter if I put the net cable on a 100Mbps switch, it keeps running at 10Mbps speed....
I know how to view/change ethernet speed... (1 Reply)
Hi,
I went to a computer store and the salesman sold me a SATA cable and told me that all SATA cables are the same. Another salesman at a different store told me a cable rated for SATA 2, which I bought, MIGHT work as well as one rate for SATA 3 but it is not guaranteed. I decided to run a... (3 Replies)
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Hi guys,
Suppose you have a server with two ethernet cards (1GB each) and each cards are connecting to two different switches cisco 3750. My question is:
How can I setup my server's network interfaces to increase the throughput up to 2GB? is it possible? If not, do you know another way to up... (3 Replies)
I have a new Sun 440 and I am trying to configure it. Non of the Ethernet ports are enabled; when I issue "ifconfig -a" it returns nothing. Is there a way to know the available port name (e.g. ce, bge, etc.) by running a command or so ? (4 Replies)
Hi Friends,
I am using intel system installed solaris 10, when i check ifconfig -a it doesn't show any thing eg-for HP servers hme0, for sun servers-iprb0. for me it doesn't show any thing, and tell me what files to be modified. Thanks in Advance. (1 Reply)
hai this is nagesh
when i was doing practical , i find some dought.
iam using solaris 9. how can i see the ethernet card speed , wheather it is halfduplex or full duplex.any body please help me (4 Replies)
I am trying to find a command to return the "link" speed of the networks installed on AIX.
ifconfig - gives me where the link is up and the duplex setting. I need to determine for example if the ethernet connection is 10, 100, 1000 Mbs or what the current speed is based on the network media... (3 Replies)
RTL8139-DIAG(8) System Manager's Manual RTL8139-DIAG(8)NAME
rtl8139-diag - EEPROM setup and diagnostic program for ethernet cards based on the Realtek 8129 and 8139 chips.
SYNOPSIS
rtl8139-diag [options]
DESCRIPTION
rtl8139-diag is a program that you can use to diagnose problems with ethernet cards based on the Realtek 8129 or 8139 chip series.
OPTIONS
These programs follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is
included below.
-h, --help
Show summary of options.
-V, --version
Show version of program.
-v, --verbose
Verbose mode.
-q, --quiet
Be very unverbose.
-# <cardnum>
Use card number <cardnum>.
-a, --show_all_registers
Print all registers.
-e, --show-eeprom
Dump EEPROM contents to stdout.
-E, --emergency-rewrite
Re-write a corrupted EEPROM.
-p, --base-address <port>
Specify port to use.
-A, --Advertise <mediaype>
Advertise media type. Valid Options are: 10baseT, 100baseT4, 100baseTx, 100baseTx-FD, 100baseTx-HD, 10baseT-FD and 10baseHD.
-F, --new-interface <interface>
Interface number. Options that make sense are: 10baseT, 10base2, AUI, 100baseTx, 10baseT-FDX, 100baseTx-FDX, 100baseT4, 100baseFx,
100baseFx-FDX, MII, Autosense and Autonegotiate.
-H, --new-hwaddress <address>
Set card to a new hardware address.
-m, --show-mii
Dump MII management registers.
-R, --reset
Reset the transceiver.
-T, --test
Do register and SRAM test.
-w, --write-EEPROM <values>
Write to the EEPROMS with the specified values. Do not use this, if you do not know what you do!
-f, --force-detection
Try to identify the card, even if it is active.
-t, --chip-type <card>
Explicitly set the chip. To get all valid numbers, run rtl8139-diag with the options '-t -1'.
SEE ALSO mii-diag(8)AUTHOR
rtl8139-diag was written and is still maintained by Donald Becker <becker@scyld.com>. This manual page was written by Alain Schroeder
<alain@debian.org>, for the Debian GNU/Linux system (but may be used by others).
February 18, 2002 RTL8139-DIAG(8)
