interface problem


 
Thread Tools Search this Thread
Top Forums UNIX for Advanced & Expert Users interface problem
# 1  
Old 05-26-2009
Error interface problem

hi all,

i have problem with my box,
until now i can't investigate the root cause of my issue at my box.
here the problem.
i have a box as a squid server just forward all request packet from one interface and receive the packet then forward to client at the same interface. but after 5 hours i can't remote that box using ssh. i try enter the server by monitoring console. then i find ssh running all not, i found ssh shown running well, then i make a argue that problem come from interface. maybe the kernel block the interface because to much packet use the interface, until now my suggestion just reboot the server directly, i need some guide from you unix expert to solve my issue.

I have a plan to make a script to monitoring ssh port connection, so every 1 hours will chech ssh can or can't at the server if can't will restart. please guide me about this script.

Thanks and BR
# 2  
Old 05-27-2009
Did you look at your netstat to see if it not some FIN_WAIT etc... issue?
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. HP-UX

Metro Cluster Interface Problem

Hi Guys, Kindly advise how to fix the down interface status in MC. Physically all nic interfaces are ok but as cmviewcl some interface are down: Node 1: Network_Parameters: INTERFACE STATUS PATH NAME PRIMARY up ... (0 Replies)
Discussion started by: batas
0 Replies

2. Solaris

Network interface problem

HI, genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex genunix: WARNING: ce0: fault detected external to device; service degraded genunix: WARNING: ce0: xcvr addr:0x01 - link down genunix: NOTICE: ce0: fault cleared external to device; service available genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies

3. Solaris

Network interface problem

Hi i have replace a NIC card on solaris 10 when i give the following command ifconfig -a it just show the lo0 (only loop back with inet 127.0.0.1) when i give the following command to config the interface, ifconfig elxl0 plumb ifconfig: plumb: elxl0: no such interface please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies

4. Debian

Problem with graphical interface

Hi, i have problems with an installation of Debian i386 505 in a pc. The hardware it is a mother soyo with a chipset via. When i install the xorg, the installation it`s succesfull, but when i type startx, the pc don`t respond. I am from Argentina and my English it isn`t good. Sorry. (0 Replies)
Discussion started by: Kritar
0 Replies

5. Programming

libcurl multi interface problem

Hello, I'm trying to use libcurl multi interface to fetch several data in parallel. I would expect this to be faster than performing repeated fetches using the easy interface, but for some reason I can't obtain any speed up at all: using the multi interface actually turns out to be MUCH slower than... (2 Replies)
Discussion started by: clalfa
2 Replies

6. IP Networking

Solaris Virtual Interface Problem in DHCP

Hi all, I am experiencing a problem with dhcp broadcast packages. these broadcast packages are seen on bge1 and bge1:1 interfaces but somehow they are not seen at bge771001 interface which is second virtual interface on the bge1 interface. I have a server on which I configured it as working... (2 Replies)
Discussion started by: ironoxide
2 Replies

7. UNIX for Dummies Questions & Answers

Multi Network card interface problem

My system info is show below:- #uname -a SunOS qfserver 5.8 Generic_117350-29 sun4u sparc SUNW,Sun-Blade-2500 and I have two network card as shown below:- #ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0:... (1 Reply)
Discussion started by: sarifudin
1 Replies

8. AIX

Problem with a Network Interface

Hi every body, I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN. When I tried to set this interface UP I encountered the following error: Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies

9. Solaris

network interface problem solaris 2.5

Hi guys, Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot). I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies

10. UNIX for Advanced & Expert Users

network interface problem

Hi expert, Need some help on network interface issue.. I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies
Login or Register to Ask a Question