10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hello All,
We are running multiple codes in prod all having different sources of databases in other servers. Many times due to network issue connectivity and DB issue the jobs got failed and to recover them become very brainstorming . I planning to create one script that can pre check if all the... (0 Replies)
Discussion started by: looney
0 Replies
2. UNIX for Dummies Questions & Answers
Hi!
I am not sure if this is the right place to post this question. What I did was to download vmware onto my laptop, them install a linux distro as a guest O.S., on VM network configuration I have used "bridge", them I used Virtual Network Editor to chose the network interface, but as I write... (4 Replies)
Discussion started by: fretagi
4 Replies
3. AIX
Hello Everyone
We have purchased IBM Pureflex chassis with 5 P460 blades. We have configured each blade with dual vios and 4 vio clients. VIOS installation and vio client installation and configuration was completed successfully.
When we tried to connect the network cables from Pureflex... (2 Replies)
Discussion started by: yuvarakasil
2 Replies
4. HP-UX
Newbie with UNIX here.
Currently troubleshooting a UNIX terminal we have.
I determined it to be bad and swapped it out with a known good terminal. I went in and changed the IP address and host name to reflect the old terminal. Although now there is no connectivity.
I swapped out the NIC... (1 Reply)
Discussion started by: kevinlord190
1 Replies
5. IP Networking
ello,
i am new to the networking side.
I have a requirement to check the tcp network connectivity between server it's running on and the list of host's and ports combination.
please help me where i am going wrong.
my code:
#!/bin/bash
#read the file line by line
cd "$1"
cat... (17 Replies)
Discussion started by: sknovice
17 Replies
6. Shell Programming and Scripting
Hello,
I have a requirement to check the tcp network connectivity between server it's running on and the list of host's and ports combination.
i have written the below code but it doesn't work, but when i execute the nc command outside the script it works fine.
please help me where i am... (8 Replies)
Discussion started by: sknovice
8 Replies
7. UNIX for Dummies Questions & Answers
red hat 5 update 4 64bit. linux newby. on an interactive boot i can ping -t my vm linux server from my physical MS XP workstation and a vm W2000 64 bit server until xend is started, after that i get destination unreachable. if i choose not to start xend on the interactive boot i retain... (1 Reply)
Discussion started by: slartibartfast9
1 Replies
8. Solaris
I have a solaris 10 x86 installed on a VMware server. It has been runing well for a couple weeks, but started to have network connectivity issue since last week. The network card seems to be up and down every one minute. So I got connection closed after I sshed to it for about one minute.
#... (2 Replies)
Discussion started by: fredao
2 Replies
9. Solaris
I have 4 V440 servers running Solaris 9. I have their interfaces configured (ce0) and have connectivity to our network. However, after reboot,...the connectivity is lost although the interface shows that its still up after an ifconfig -a.
Only after I reconfigure the interface do I restore... (19 Replies)
Discussion started by: StorageGuy
19 Replies
10. IP Networking
Hi,
I would like to know how i can setup my unix computer to connect to novell. Anybody any idea? (5 Replies)
Discussion started by: edw1ns
5 Replies
CREATE
VIEW(7) SQL Commands CREATE VIEW(7)
NAME
CREATE VIEW - define a new view
SYNOPSIS
CREATE [ OR REPLACE ] [ TEMP | TEMPORARY ] VIEW name [ ( column_name [, ...] ) ]
AS query
DESCRIPTION
CREATE VIEW defines a view of a query. The view is not physically materialized. Instead, the query is run every time the view is referenced
in a query.
CREATE OR REPLACE VIEW is similar, but if a view of the same name already exists, it is replaced. The new query must generate the same col-
umns that were generated by the existing view query (that is, the same column names in the same order and with the same data types), but it
may add additional columns to the end of the list. The calculations giving rise to the output columns may be completely different.
If a schema name is given (for example, CREATE VIEW myschema.myview ...) then the view is created in the specified schema. Otherwise it is
created in the current schema. Temporary views exist in a special schema, so a schema name cannot be given when creating a temporary view.
The name of the view must be distinct from the name of any other view, table, sequence, or index in the same schema.
PARAMETERS
TEMPORARY or TEMP
If specified, the view is created as a temporary view. Temporary views are automatically dropped at the end of the current session.
Existing permanent relations with the same name are not visible to the current session while the temporary view exists, unless they
are referenced with schema-qualified names.
If any of the tables referenced by the view are temporary, the view is created as a temporary view (whether TEMPORARY is specified
or not).
name The name (optionally schema-qualified) of a view to be created.
column_name
An optional list of names to be used for columns of the view. If not given, the column names are deduced from the query.
query A SELECT [select(7)] or VALUES [values(7)] command which will provide the columns and rows of the view.
NOTES
Currently, views are read only: the system will not allow an insert, update, or delete on a view. You can get the effect of an updatable
view by creating rules that rewrite inserts, etc. on the view into appropriate actions on other tables. For more information see CREATE
RULE [create_rule(7)].
Use the DROP VIEW [drop_view(7)] statement to drop views.
Be careful that the names and types of the view's columns will be assigned the way you want. For example:
CREATE VIEW vista AS SELECT 'Hello World';
is bad form in two ways: the column name defaults to ?column?, and the column data type defaults to unknown. If you want a string literal
in a view's result, use something like:
CREATE VIEW vista AS SELECT text 'Hello World' AS hello;
Access to tables referenced in the view is determined by permissions of the view owner. However, functions called in the view are treated
the same as if they had been called directly from the query using the view. Therefore the user of a view must have permissions to call all
functions used by the view.
When CREATE OR REPLACE VIEW is used on an existing view, only the view's defining SELECT rule is changed. Other view properties, including
ownership, permissions, and non-SELECT rules, remain unchanged. You must own the view to replace it (this includes being a member of the
owning role).
EXAMPLES
Create a view consisting of all comedy films:
CREATE VIEW comedies AS
SELECT *
FROM films
WHERE kind = 'Comedy';
COMPATIBILITY
The SQL standard specifies some additional capabilities for the CREATE VIEW statement:
CREATE VIEW name [ ( column_name [, ...] ) ]
AS query
[ WITH [ CASCADED | LOCAL ] CHECK OPTION ]
The optional clauses for the full SQL command are:
CHECK OPTION
This option has to do with updatable views. All INSERT and UPDATE commands on the view will be checked to ensure data satisfy the
view-defining condition (that is, the new data would be visible through the view). If they do not, the update will be rejected.
LOCAL Check for integrity on this view.
CASCADED
Check for integrity on this view and on any dependent view. CASCADED is assumed if neither CASCADED nor LOCAL is specified.
CREATE OR REPLACE VIEW is a PostgreSQL language extension. So is the concept of a temporary view.
SEE ALSO
ALTER VIEW [alter_view(7)], DROP VIEW [drop_view(7)]
SQL - Language Statements 2010-05-14 CREATE VIEW(7)