Installfest at LinuxWorld could seed national program
07-28-2008 01:00 PM
IDG World Expo has teamed up with open source security gateway provider Untangle and electronics recycler Alameda County Computer Resource Center (ACCRC) to host an <ahref="http://www.linuxworldexpo.com/live/12/ehall//SN264817">Installfest for Schools at LinuxWorld Conference and Expo in San Francisco next week. Volunteers will refurbish older discarded computers with free and open source software (FOSS) before they are donated to schools in need.
Hi,
What I have done - I installed my national language(package bos.loc.pc.Lt_LT), and selected this language for particular user using LANG env. variable.
What should I do next ?
I heard something about keymaps, input methods ??
(my language is lithuanian)
I'm talking only about command... (0 Replies)
LinuxWorld Expo is going on this week at the Moscone Center in San Francisco, CA. I'll be there Tues, Weds, Thurs. Anyone else from the forums planning to attend? (0 Replies)
TRACEROUTE6(8) BSD System Manager's Manual TRACEROUTE6(8)NAME
traceroute6 -- print the route IPv6 packets will take to a network node
SYNOPSIS
traceroute6 [-dIlnNrvU] [-f firsthop] [-g gateway] [-m hoplimit] [-p port] [-q probes] [-s src] [-w waittime] target [datalen]
DESCRIPTION
The traceroute6 utility uses the IPv6 protocol hop limit field to elicit an ICMPv6 TIME_EXCEEDED response from each gateway along the path to
some host.
The only mandatory parameter is the destination host name or IPv6 address. The default probe datagram carries 12 bytes of payload, in addi-
tion to the IPv6 header. The size of the payload can be specified by giving a length (in bytes) after the destination host name.
Other options are:
-d Debug mode.
-f firsthop
Specify how many hops to skip in trace.
-g gateway
Specify intermediate gateway (traceroute6 uses routing header).
-I Use ICMP6 ECHO instead of UDP datagrams.
-l Print both host hostnames and numeric addresses. Normally traceroute6 prints only hostnames if -n is not specified, and only numeric
addresses if -n is specified.
-m hoplimit
Specify maximum hoplimit, up to 255. The default is 30 hops.
-n Do not resolve numeric address to hostname.
-N Use a packet with no upper layer header for the probes, instead of UDP datagrams.
-p port
Set UDP port number to port.
-q probes
Set the number of probe per hop count to probes.
-r Bypass the normal routing tables and send directly to a host on an attached network. If the host is not on a directly-connected net-
work, an error is returned. This option corresponds to the SO_DONTROUTE socket option; it can be used to ping a local host through
an interface that has no route through it (e.g., after the interface was dropped by a routing daemon).
-s src Src specifies the source IPv6 address to be used.
-U Use UDP datagrams for the probes. This is the default.
-v Be verbose.
-w waittime
Specify the delay time between probes.
This program prints the route to the given destination and the round-trip time to each gateway, in the same manner as traceroute.
Here is a list of possible annotations after the round-trip time for each gateway:
!N Destination Unreachable - No Route to Host.
!P Destination Unreachable - Administratively Prohibited.
!S Destination Unreachable - Not a Neighbour.
!A Destination Unreachable - Address Unreachable.
! This is printed if the hop limit is <= 1 on a port unreachable message. This means that the packet got to the destination, but
that the reply had a hop limit that was just large enough to allow it to get back to the source of the traceroute6. This was
more interesting in the IPv4 case, where some IP stack bugs could be identified by this behaviour.
RETURN VALUES
The traceroute6 utility will exit with 0 on success, and non-zero on errors.
SEE ALSO ping(8), ping6(8), traceroute(8)HISTORY
The traceroute6 utility first appeared in WIDE hydrangea IPv6 protocol stack kit.
BSD May 17, 1998 BSD