Simplifying infrared device configuration

9 More Discussions You Might Find Interesting

1. Red Hat

[nmcli] Where is the configuration file of device (redhat 7)

OS is redhat 7. # nmcli dev DEVICE TYPE STATE CONNECTION virbr0 bridge disconnected -- eno16777736 ethernet disconnected -- eno33554960 ethernet disconnected -- virbr0-nic ethernet disconnected -- lo ...

2. AIX

0514-516 Device Configuration Database Lock Service

Hello guys, on one of our AIX VIO LPARs I can not remove hdiskpower devices, which seemed to presented to the VIO in an incorrect way and behaviour (not all paths can be seen, pseudo device name is unknown etc.) Therefor I decided to deattach the hdiskpower device from PowerPath controll by: ...

3. Shell Programming and Scripting

Help with Backup Shell Script for Network Device Configuration backup

HI all, im new to shell scripting. need your guidence for my script. i wrote one script and is attached here Im explaining the requirement of script. AIM: Shell script to run automatically as per scheduled and backup few network devices configurations. Script will contain a set of commands...

4. Shell Programming and Scripting

Simplifying sed/tr

Hi all, I don't have much experience with shell scripting and I was wondering if there's a shorter way to write this. Basically, given a list of strings separated by new lines, I want to prepend each string with a prefix and separate the strings with commas i.e. stra strb strc becomes...

5. Shell Programming and Scripting

need help simplifying an if statement

the code below is a small fragment of the actual line, in fact i have about 20 values i'm comparing and want to know if it can be simplified. other than the x.xx.xx format of the value they have nothing in common if || || ; then do this else do this fiany suggestions?

6. UNIX for Advanced & Expert Users

Simplifying my script

Hi, Is there a way to simplify the below script? Because I am having problems executing this if I added this to CRON. Also, you may notice that its objective is to put all information in one file (rm1.txt). And in addition file "sRMR_6.txt" to sRMR_23.txt" changes its information everyday....

7. Shell Programming and Scripting

simplifying awk

tcpdump -nr testdump|awk '!/:/;gsub(/^+|+$/,""){print $3};a!~$0;{a=$0};{print $3};!/length/;/./;!/11\:/;!/8 7 6 5 4 3 2 1/;!/UDP/{b=$0} END {for (j=i-1; j>=0; ) print b };{for (i=NF; i>0; i--) printf("%s ",i);printf ("\n")}' *NOTE IN j>=0 the ; ) was given a space since a smiley is showing up......

8. Shell Programming and Scripting

Simplifying the For loop

Is there a way to simplify stating 1 through to 10, for example in a for loop construct? for x in 1 2 3 4 5 6 7 8 9 10 do .... done I have tried (1-10) with no luck.. thanks

9. Shell Programming and Scripting

Help in simplifying a sed command

I need to do a substitution: CPF to ,C,P,F, CPM to ,C,P,M, SPF to ,S,P,F etc. I can do each of them with separate substitutions e.g. s/CPF/,C,P,F/ but I'd like to know if there is a more elegant solution. In general, how can I use the results of the search in the substitution, ...

LEARN ABOUT DEBIAN

snd_gusc

SND_GUSC(4)						   BSD Kernel Interfaces Manual 					       SND_GUSC(4)

NAME

     snd_gusc -- Gravis UltraSound ISA bridge device driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

	   device sound
	   device snd_gusc

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

	   snd_gusc_load="YES"

     Non-PnP cards require the following lines in device.hints(5):

	   hint.gusc.0.at="isa"
	   hint.gusc.0.port="0x220"
	   hint.gusc.0.irq="5"
	   hint.gusc.0.drq="1"
	   hint.gusc.0.flags="0x13"

DESCRIPTION

     The snd_gusc bridge driver allows the generic audio driver sound(4) to attach to Gravis UltraSound sound cards.

     The value of flags specifies the secondary DMA channel.  If the secondary DMA channel is C, set the flags to (C | 0x10).  For a sound card
     without the secondary DMA channel, the flags should be set to zero.

HARDWARE

     The snd_gusc driver supports the following sound cards:

     o	 Gravis UltraSound MAX
     o	 Gravis UltraSound PnP

DIAGNOSTICS

     xxx: gus pcm not attached, out of memory  There are not enough memory to drive the device.

SEE ALSO

     sound(4)

HISTORY

     The snd_gusc device driver first appeared in FreeBSD 4.0.

AUTHORS

     Ville-Pertti Keinonen <will@iki.fi>
     Seigo Tanimura <tanimura@r.dl.itc.u-tokyo.ac.jp>

BUGS

     Recording pcm sound data is not supported yet.

BSD
								 December 15, 2005							       BSD

UNIX and Linux RSS News