9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I m not sure if this is a right question to ask .
During the installation of the OS, installation sw does partitioning for you.
I m not quit sure if they have used parted or fdisk to partition the disk.
(If they are using fdisk then you can't make partition > 2Tb )correct me if i m wrong.Also... (5 Replies)
Discussion started by: pinga123
5 Replies
2. Red Hat
Hi Everyone,
I have added new Virtual disk to OS. The main point is I need to bring this whole Disk into LVM control, is it necessary to partition the disk using fdisk command and assign partition type as '8e', or can I directly add that disk into LVM, by running pvcreate command with out... (2 Replies)
Discussion started by: bobby320
2 Replies
3. Red Hat
I'm new to Linux 5, going through initial phases of installation and setting up devices, etc,, and much to my surprise discovered also an existence of a 2nd hard drive to try to initialize and partition perhaps using any built-in command i.e. "fdisk" or similar, but I couldn't get the command to... (4 Replies)
Discussion started by: su
4 Replies
4. Solaris
Hi all
I'm having difficulty setting up a proper disk structure on a 72GB HDD. The drive was previously part of a zfs pool. The zpool has ben destroyed and now I want to use the disk in a raid 5 array. I need to partition the disk accordingly though.
This is what the partition table currently... (7 Replies)
Discussion started by: notreallyhere
7 Replies
5. What is on Your Mind?
Do you think it would be useful to have a section where members review products?
Please vote and comment :b:
Thanks! (12 Replies)
Discussion started by: Neo
12 Replies
6. Solaris
Total disk size is 38912 cylinders
Cylinder size is 32130 (512 byte) blocks
Cylinders
Partition Status Type Start End Length %
========= ====== ============ ===== === ====== ===
... (2 Replies)
Discussion started by: seyiisq
2 Replies
7. Solaris
Hi guys,
I havent done this before but iam trying to create an image of a mirrorred drive.
Correct me if iam wrong, but when i have two disks setup in raid configuration and have them mirrored in solaris. It then defines at one entity.
How would i create a "flar" image of that one entity... (3 Replies)
Discussion started by: tlee
3 Replies
8. Shell Programming and Scripting
Hello!
I need to write partitioning script wich would work in rescue mode. It will prepare partitions and unpack linux on it. However I need to calculate whole size of the disk and create:
/dev/sda1 --> One big partition (minus (2*size of memory) for swap)
/dev/sda2 --> Swap partition... (1 Reply)
Discussion started by: pug123
1 Replies
9. UNIX for Dummies Questions & Answers
Hello,
To run UNIX, can the hard disk be partitioned so I could use that part for UNIX and the other for my existing Windows '98? At the moment there are hard drives C: & D:. Also, where can I obtain the UNIX software?.....Your response is appreciated. (2 Replies)
Discussion started by: hpin
2 Replies
raw2hdf(1) Emulators raw2hdf(1)
NAME
raw2hdf - Create an .hdf hard disk image from a raw data file
SYNOPSIS
raw2hdf rawfile hdffile
DESCRIPTION
raw2hdf converts a binary dump of a hard disk's data into an IDE disk image in .hdf format for use with Sinclair ZX Spectrum emulators.
OPTIONS
-v version
specifies the version of .hdf image to be created. Valid values are `1.0' for a version 1.0 file and `1.1' for a version 1.1 file.
Defaults to creating version 1.1 files.
rawfile
specifies a raw data file (or block device corresponding to an actual disk) to be converted.
hdffile
specifies the .hdf file to create.
NOTES
Since raw2hdf has no knowledge of the geometry of the disk from which the original image was taken (indeed, the input file need not origi-
nate from a real IDE disk at all), there is no guarantee that the information contained in the .hdf file header accurately represents the
original disk. However, it will attempt to construct a header that is consistent with the size of the image, to produce an .hdf file which
is functionally equivalent.
BUGS
None known.
SEE ALSO
fuse(1), fuse-utils(1), libspectrum(3)
The .hdf format specification, at
http://www.ramsoft.bbk.org/hdfform.html.
The comp.sys.sinclair Spectrum FAQ, at
http://www.worldofspectrum.org/faq/index.html.
AUTHOR
Matthew Westcott (matthew@west.co.tt).
Version 1.0.0 16th December, 2010 raw2hdf(1)