After thrashing about in the wilds of Googland I came up with the following configuration steps. I had it working at one point but it sure ain't worin now! Could someone look at it and see where I went wrong? Thanks!
Code:
Rt. Click: on XMMS panel
Click: Options > Preferences
AUDIO I/O PLUGINS--
Input Plugins, Click: CD Audio Player 1.2.11
Press: Configure
CD Audio Player--
Device & Drive 1:
For Device enter: /dev/cdrom
For Directory enter: /mnt/cdrom
For Play Mode click: Digital Audio Extraction
(ignores whether there is an audio cable connected)
Click: Check Drive
Click: Close on pop-up dialog box
Note: Click on Add Drive only if needing multiple drives
Click: OK
Output Plugins, Click: ALSA 1.2.11
Press: Configure
ALSA Driver pop-up should have:
Audio device=default and
Mixer device=Master
Select: Mixer card=VIA 8235
Press: OK
Press: APPLY
Press: OK (AUDIO/I/O PLUGINS)
Last edited by Scott; 03-31-2012 at 10:37 AM..
Reason: Code tags
I'm trying to record audio using Audacity 2.0.5 installed from SlackBuilds. My system is 64-bit Slackware 14.1 and a sound card is Intel HD Audio. I didn't change my sound system to OSS. (Default sound system in Slackware 14.1 is ALSA, isn't it?) First, I set Internal Microphone slider in KMix... (2 Replies)
Hi
I have misplaced my Solaris 8 02/04 CDs - is there any way to get a copy? I have to re-install a server and it needs to be this version.
Mick (2 Replies)
Dear all,
I have been using suse linux for as long as I can remember. However, for every installation I get the same problem.
Once the installation is completed, and all of my devices (brand new hardware, from reknown brands) are detected, I decide to start doing some work, and play some... (2 Replies)
I have a 500mhz K6 that I'm running Red Hat 8 on. I use xmms for all my music media playing purposes, but There seems to be an issue between xmms and volume control. Every now and then when I adjust the volume through aumix xmms freezes up and sends the sound into a runaway loop that I cant seem... (2 Replies)
sid2wav(1) User Commands sid2wav(1)NAME
sid2wav - output wav files out of sid files
SYNOPSIS
sid2wav [-commands] <datafile>|- [outputfile]
DESCRIPTION
Sid2wav is a synthetic waveform generator from sid files, named after the Sound Interface Chip found in Commodore 64 personal computers.
With this tool, one can 'convert' sid files to wav ones that popular music players like XMMS can play. Note that you don't have to convert
sid files just to listen them, sidplay can play it for you just as it would sound on a real C64. Also, XMMS has an input plugin to play sid
files directly. The use is that you may convert sid tunes to wav and later to any compressed format like Ogg or MP3 for users lacking sid-
play. Other use would be to convert files to wav for audio CD creation.
COMMANDS -h gives help on usage.
-f<num>
set frequency in Hz (default: 44100).
-16 16-bit (default: 8-bit)
-s stereo (default: mono).
-ss enable stereo surround.
-u au output (8000Hz mono 8-bit u-law).
-o<num>
set song number (default: preset).
-a improve PlaySID compatibility (not recommended).
-a2 transparent ROM memory mode (overrides -a).
-n enable NTSC-clock speed for VBI tunes (not recommended).
-nf no SID filter emulation.
-ns MOS 8580 waveforms (default: MOS 6581).
-m<num>
mute voices out of 1,2,3,4 (default: none). Example: -m13 (voices 1 and 3 off).
-t<num>
set seconds to play (default: 60).
-b<num>
skip first <num> seconds into the song (default: 0).
-fin<num>
fade-in time in seconds (default: 0).
-fout<num>
fade-out time in seconds (default: 2).
SEE ALSO sidplay(1), xmms (1).
AUTHORS
Michael Schwendt <sidplay@geocities.com>
Adam Lorentzon <d93-alo@nada.kth.se>
This manpage was written for the Debian GNU/Linux system by Laszlo 'GCS' Boszormenyi <gcs@lsc.hu> (but may be used by others).
Sidplay May, 2004 sid2wav(1)
