I have two Sun Fire X4100 machines with Ubuntu 12.04 installed on them.
I am able to configure the Net Mgt port with an IP address and access the ILOM from the browser. I can also boot the Ubuntu installed and redirect the output.
The issue i have is that when i configure the network interface(NET0) from Ubuntu and connect an ethernet cable to it i am unable to reach it via ping or ssh. I am also unable to ping out from it. I can confirm that all the network parameters(IP address,Netmask,gateway) are set correctly. And the NET0 interface is connected to the same switch the Net Mgt is connected to. I can ssh and ping the Net Mgt but not the NET0 interface.
Hello,
I have purchaced an old SUn fire x2270 server .
I wanted to make ILOM upgrade to the latest version of software :
ILOM 3.0.9.18.a r126592
BIOS vers. 2.09
Server 2.2.3
(10-Aug-2018)
Because my version is very outdated.
But i can't download the updatebecause it's require... (4 Replies)
I have a problem,
I have been installing Redhat Interprise Linux on X4100 M2 Server, when system is reboot after install, the server is restart (reboot) again (alias unlimited).
The bios system show message error "Multi-bit ECC Error" and "bank interleave requested but not enable"
I have... (5 Replies)
I switched on the power to the server. But, the server did not power on i.e., none of the 3 LEDs on the front panel is lighted.
(Power supplies are showing only amber LEDs with "Ready to remove" sign).
I tried to turn on the power supplies via System Controller menu (platform shell), but it... (6 Replies)
Hello all.
I have a requirement to install a aftermarket video card in the server, can you advise what fits? or if there is a sun riser part which convers the PCIx slot to PCIe
The unit is a standard x4100 with PCIx slots, not an M2 with the PCIe slots.
thanks (4 Replies)
hi
please how to know that a sun x4100 m2 server has one or two processors installed ?? the OS installed on this server is windows 2003 Enterprise Edition.
thanks (2 Replies)
I have looked all over the bios configuration to enable hardware virtualization and found nothing. Could someone tell if this server support it and if so where I go to enable that feature. By the way this is a x86 server. (0 Replies)
I am new to Sun.
I brought Sun Fire 280R to practice UNIX. What are the requirements for the monitor/CRT? Will it burn out old non-Sun CRTs? Does it need LCD monitor?
Thanks. (3 Replies)
Hello all,
I'm lost and can't figure this problem out.
I have a Sun fire 280R running Solaris 8. Everything was working great. I have one drive in bay 1(not 0). But when I reboot the system it trys to open files in /dev/rdsk/c1t1d0s0. Should it have been opeing /dev/rdsk/c1t0d0s0, the... (4 Replies)
I still haven't got an answer to this question...
Excerpt from My SysAd Blog
A colleague of mine is having a problem with a Sun Fire v1280 server crashing. He tried Googling for the error message in red but hasn't found anything yet. Your insights would be greatly appreciated.
"cannot... (2 Replies)
SYNCPACKAGE(1) General Commands Manual SYNCPACKAGE(1)NAME
syncpackage - copy source packages from Debian to Ubuntu
SYNOPSIS
syncpackage [options] <.dsc URL/path or package name>
DESCRIPTION
syncpackage causes a source package to be copied from Debian to Ubuntu.
syncpackage allows you to upload files with the same checksums of the Debian ones, as the common script used by Ubuntu archive administra-
tors does, this way you can preserve source files integrity between the two distributions.
syncpackage will detect source tarballs with mismatching checksums, and can perform fake syncs.
WARNING
The use of syncpackage --no-lp, which generates a changes file to be directly uploaded to the Ubuntu primary archive or a PPA, is discour-
aged by the Ubuntu Archive Administrators, as it introduces an unnecessary window for error. This only exists for backward compatibility,
for unusual corner cases (such as fakesyncs), and for uploads to archives other than the Ubuntu primary archive. Omitting this option will
cause Launchpad to perform the sync request directly, which is the preferred method for uploads to the Ubuntu primary archive.
OPTIONS -h, --help
Show help message and exit
-d DIST, --distribution=DIST
Debian distribution to sync from. Default is testing during LTS cycles, and unstable otherwise.
-r RELEASE, --release=RELEASE
Specify target Ubuntu release. Default: current development release.
-V DEBVERSION, --debian-version=DEBVERSION
Specify the version to sync from.
-c COMPONENT, --component=COMPONENT
Specify the component to sync from.
-b BUG, --bug=BUG
Mark a Launchpad bug as being fixed by this upload.
-s USERNAME, --sponsor=USERNAME
Sponsor the sync for USERNAME (a Launchpad username).
-v, --verbose
Display more progress information.
-F, --fakesync
Perform a fakesync, to work around a tarball mismatch between Debian and Ubuntu. This option ignores blacklisting, and performs a
local sync. It implies --no-lp, and will leave a signed .changes file for you to upload.
-f, --force
Force sync over the top of Ubuntu changes.
--no-conf
Do not read any configuration files, or configuration from environment variables.
-l INSTANCE, --lpinstance=INSTANCE
Launchpad instance to connect to (default: production).
--simulate
Show what would be done, but don't actually do it.
LOCAL SYNC PREPARATION OPTIONS
Options that only apply when using --no-lp:
--no-lp
Construct sync locally, rather than letting Launchpad copy the package directly. It will leave a signed .changes file for you to
upload. See the WARNING above.
-n UPLOADER_NAME, --uploader-name=UPLOADER_NAME
Use UPLOADER_NAME as the name of the maintainer for this upload instead of evaluating DEBFULLNAME and UBUMAIL. This option may only
be used in --no-lp mode.
-e UPLOADER_EMAIL, --uploader-email=UPLOADER_EMAIL
Use UPLOADER_EMAIL as the email address of the maintainer for this upload instead of evaluating DEBEMAIL and UBUMAIL. This option
may only be used in --no-lp mode.
-k KEYID, --key=KEYID
Specify the key ID to be used for signing.
--dont-sign
Do not sign the upload.
-d DEBIAN_MIRROR, --debian-mirror=DEBIAN_MIRROR
Use the specified mirror. Should be in the form http://ftp.debian.org/debian. If the package isn't found on this mirror, syncpack-
age will fall back to the default mirror.
-s UBUNTU_MIRROR, --debsec-mirror=UBUNTU_MIRROR
Use the specified Debian security mirror. Should be in the form http://archive.ubuntu.com/ubuntu. If the package isn't found on
this mirror, syncpackage will fall back to the default mirror.
ENVIRONMENT
DEBFULLNAME, DEBEMAIL, UBUMAIL
Used to determine the uploader (if not supplied as options). See ubuntu-dev-tools(5) for details.
All of the CONFIGURATION VARIABLES below are also supported as environment variables. Variables in the environment take precedence to
those in configuration files.
CONFIGURATION VARIABLES
The following variables can be set in the environment or in ubuntu-dev-tools(5) configuration files. In each case, the script-specific
variable takes precedence over the package-wide variable.
SYNCPACKAGE_DEBIAN_MIRROR, UBUNTUTOOLS_DEBIAN_MIRROR
The default value for --debian-mirror.
SYNCPACKAGE_UBUNTU_MIRROR, UBUNTUTOOLS_DEBSEC_MIRROR
The default value for --ubuntu-mirror.
SYNCPACKAGE_KEYID, UBUNTUTOOLS_KEYID
The default value for --key.
SEE ALSO requestsync(1), ubuntu-dev-tools(5)AUTHOR
syncpackage was written by Martin Pitt <martin.pitt@canonical.com> and Benjamin Drung <bdrung@ubuntu.com>.
This manual page were written by Luca Falavigna <dktrkranz@ubuntu.com>
Both are released under GNU General Public License, version 3.
ubuntu-dev-tools June 2010 SYNCPACKAGE(1)