9 More Discussions You Might Find Interesting
1. Red Hat
Hi to all,
I have RHEL 6.4 and NVIDIA GeForce 210 graphics card. After disabling nouveau and installing driver NVIDIA-Linux-x86_64-319.17.run
display is enormous. I did like this :-
# cd /lib/modules/$(uname -r)/kernel/drivers/gpu/drm/nouveau
# mv nouveau.ko nouveau.ko.bak
# cd /boot
#... (3 Replies)
Discussion started by: rahulvishwa
Anyone know any commands to verify the graphics card is installed correctly on an M4000?
show-displays just comes back and echoes nothing.
Also there is on input-device or output-device variable when you run printenv.
This in itself is worrying.
Any advice would be... (4 Replies)
Discussion started by: callmebob
I'm trying to install Oracle on HP-UX 11.23. The Oracle installer needs an X server running on the box. You then start an X client on your PC, export the DISPLAY on UNIX and the installer displays on your PC. The problem is that my HP boxes do not have graphics cards installed. ... (6 Replies)
Discussion started by: kskywr
4. UNIX Desktop Questions & Answers
Does Red Hat Fedora support Nvidia card 8800GTX and 260 card?
Does any Linux OS support Nvidia card? (1 Reply)
Discussion started by: sito
5. UNIX for Dummies Questions & Answers
I am on an HP C8000 running B.11.11, I have no idea how to tell what graphics card I have...and the amount of memory it has, driver, etc. Also, how do I tell how much ram the box itself has, and other memory information like swap and processor speed and all that. Any help out there for me? ... (1 Reply)
Discussion started by: satraver
is it possible to swap the Turbo XGX graphics card in the SS5 to the ULTRA server 1 ? and do they use the same type of RAM ?
Thx. (0 Replies)
Discussion started by: mads-nielsen
Hi All -
I looked through this forum and a couple of other places without success. Maybe someone here can help. I very recently came into possession of a p520, a 9131-52A. It arrived without documentation, mouse, keyboard, or graphics card.
I managed to get ASMI to work on both DB-9 ports... (6 Replies)
Discussion started by: MikeJ
Can anybody help me with regards to the driver of GXT250P graphics adapter. I have searched the web for the fileset devices.pci.14103c00 however no success was found. My current AIX version is 4.1.5 and my machine is 7043-140. My installation AIX CD is not working anymore, so I... (0 Replies)
Discussion started by: bright_genius
9. Filesystems, Disks and Memory
I have a SuSE8.1 Linux box running as a testing webserver to my small network. It's administered through ssh and webmin entirely, and doesn't have a monitor.
I could really do with the graphics card for another machine, but if I take it out, I can't start the machine up.
Any ideas how I can... (6 Replies)
Discussion started by: mistafeesh
NVE(4) BSD Kernel Interfaces Manual NVE(4)
nve -- NVIDIA nForce MCP Networking Adapter device driver
To compile this driver into the kernel, place the following lines in your kernel configuration file:
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
The nve driver provides support for the NVIDIA nForce MCP and nForce2 MCP2 networking adapter that is embedded in the southbridge of most
nForce and nForce2 motherboards.
This driver is a reimplementation of the NVIDIA supported Linux nvnet driver and uses the same closed source API library to access the under-
lying hardware. There is currently no programming documentation available for this device, and therefore little is known about the internal
architecture of the MAC engine itself.
The nve driver supports the following media types:
autoselect Enable autoselection of the media type and options.
10baseT/UTP Set 10Mbps operation.
100baseTX Set 100Mbps (Fast Ethernet) operation.
1000baseTX Set 1000Mbps (Gigabit Ethernet) operation.
The nve driver supports the following media options:
full-duplex Set full duplex operation.
For more information on configuring this device, see ifconfig(8).
The nve driver supports the NVIDIA MCP onboard adapters of mainboards with the following chipsets:
nve%d: couldn't map memory A fatal initialization error has occurred.
nve%d: couldn't map interrupt A fatal initialization error has occurred.
nve%d: failed to allocate memory There are not enough mbufs available for allocation.
nve%d: device timeout The device has stopped responding to the network, or there is a problem with the network connection (cable).
There are reports that when the card is in auto select mode, ifconfig output reports a 10baseT/UTP output while the LEDs and bandwidth show
that the card is actually in 100baseTX mode.
altq(4), arp(4), miibus(4), netintro(4), ng_ether(4), rgephy(4), ifconfig(8)
The nve driver first appeared in FreeBSD 6.0.
The nve driver was written by Quinton Dolan <email@example.com> and David E. O'Brien <obrien@FreeBSD.org>.
BSD January 16, 2011 BSD