10 More Discussions You Might Find Interesting
1. AIX
Hi,
when I boot I get an E1DC error code. I've looked it up and it says that this error occurs during the firmware check. But the error is called "Dynamic Console Selection" .
1- Machine stopped at LCD led display = E1DC = CA00E1DC
E1DC Dynamic console selection. (maybe cable or keyboard)... (3 Replies)
Discussion started by: filosophizer
3 Replies
2. AIX
Hi guys,
My company just bought pseries server from ibm,
would like to ask , if first i need to install HMC for creating lpars ?
or first i need to install aix , and then install hmc?
Thx, (3 Replies)
Discussion started by: prpkrk
3 Replies
3. AIX
Hello,
I'm very rookie to AIX and attempting to install AIX. I have vio ready on the machine and don't know how to install OS? Inserted Volume 1 DVD into the ROM, don't know what to do next. Searched many forum but cant find the this basic thing. Please let me know how to install AIX on this... (4 Replies)
Discussion started by: pjeedu2247
4 Replies
4. AIX
Hello,
I installed PowerVM IVM Virtual I/O on P-550 but later found out that the machine isn't activated for CoD VET code for virtualization.
So when booted , it goes into OPEN Firmware
I/O Hosting requires a hosting partition boot not permitted exit called
> ok
Panel shows > IO... (3 Replies)
Discussion started by: filosophizer
3 Replies
5. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
6. Linux
Anyone can help me answer the question.
Why does they use Linux on IBM pSeries not AIX.
I can't understand why, cause AIX is the best supporting from IBM pSeries.
Tks you. (3 Replies)
Discussion started by: quan0509
3 Replies
7. AIX
Hello Gurus,
i'm quite new person in AIX world, actually i'm SAP consultant. But due to my job faced with AIX.
Trying to configure new server for installation SAP. We have 4 disks one of them (hdisk3) has VG rootvg. How i can extend rootvg with another disk?
i tried:
# extendvg rootvg hdisk0... (2 Replies)
Discussion started by: sapbcer
2 Replies
8. AIX
Hi All --
I have an old 7028-6C1 which I'm using to learn AIX. The system didn't include a graphics card, so I connected via the serial port and performed a fresh install of AIX 5L V5.3.
Later, I purchased a GXT135P (2849) graphics card, and added it to the system. When I ran diag, I was able... (2 Replies)
Discussion started by: i386tech
2 Replies
9. UNIX for Dummies Questions & Answers
I'm new with UNIX, i have a pseries server from IBM and i need to install AIX 4.3, i never used wyse terminal or AIX, i need help to know how to install it, i have the server and the wyse i get in into the aixterm, over com1 but i don't know wich command use or what to do to install it..... ... (0 Replies)
Discussion started by: Juan-ito
0 Replies
10. AIX
I have been given some pSeries AIX servers to maintain. One of the servers wont come up after a shutdown and the following code is showing on the server:
10118401
How do I look up the error code? (2 Replies)
Discussion started by: dangral
2 Replies
vxpfto(1M) vxpfto(1M)
NAME
vxpfto - set Powerfail Timeout (pfto)
SYNOPSIS
vxpfto -g diskgroup -t timeout
vxpfto [-g diskgroup] -t timeout volume_list
vxpfto [-g diskgroup] -o pftostate={enabled|disabled}
vxpfto [-g diskgroup] -o pftostate={enabled|disabled} volume_list
DESCRIPTION
Powerfail Timeout is an attribute of a SCSI disk connected to an HP-UX host (see the pfto(7) man page). The vxpfto command sets the Power-
fail Timeout interval on a set of Volume Manager disks, either all disks in a disk group, or all disks underlying the volumes listed.
The first form of the command sets the same PFTO value for all the disks in the specified VxVM diskgroup.
In the second form, all disks underlying the given list of volumes are selected, optionally restricted by the disk group specified with the
-g option. If you specify a diskgroup, any volume in the list not belonging to the diskgroup is ignored.
Use the -o pftostate option to disable or enable PFTO. By default, PFTO is enabled. You can enable PFTO either on all disks in a disk
group, or on all disks underlying the volumes listed.
If you invoke vxpfto without arguments, it displays a usage message.
OPTIONS
-g diskgroup
Specifies the disk group for the operation, either by disk group ID or by disk group name.
-o pftostate={enabled|disabled}
Enables or disables the use of PFTO for IO.
-t timeout
Specifies the PFTO value in seconds. The value must be zero or a positive integer. Zero represents the system default PFTO
value. The default value depends on the disk driver controlling the disk device.
volume_list
A list of VxVM volume names. List items must be separated by white-space.
EXIT CODES
vxpfto returns a zero if successful. If it encounters an error, vxpfto exits and displays a message on standard error. Defined exit codes
are:
0 Success.
1 No PFTO value specified.
2 No diskgroup or volume list specified.
3 Illegal PFTO value specified.
EXAMPLES
Set the PFTO value on all disks in disk group testdg to 100 seconds:
vxpfto -t 100 -g testdg
Set the PFTO value to 50 seconds on all disks underlying volume01 and volume02 in disk group testdg:
vxpfto -t 50 -g testdg volume01 volume02
Set the PFTO value to 300 seconds on all disks underlying volume01 and volume02, even though they are not in the same disk group:
vxpfto -t 300 volume01 volume02
Disable PFTO on all disks in disk group testdg:
vxpfto -g testdg -o pftostate=disabled
Enable PFTO on all disks underlying volume01 and volume02i in disk group testdg:
vxpfto -g testdg -o pftostate=enabled volume01 volume02
SEE ALSO
vxdisk(1M), pfto(7)
VxVM 5.0.31.1 24 Mar 2008 vxpfto(1M)
