10 More Discussions You Might Find Interesting
1. AIX
Hi,
when I boot I get an E1DC error code. I've looked it up and it says that this error occurs during the firmware check. But the error is called "Dynamic Console Selection" .
1- Machine stopped at LCD led display = E1DC = CA00E1DC
E1DC Dynamic console selection. (maybe cable or keyboard)... (3 Replies)
Discussion started by: filosophizer
3 Replies
2. AIX
Hi guys,
My company just bought pseries server from ibm,
would like to ask , if first i need to install HMC for creating lpars ?
or first i need to install aix , and then install hmc?
Thx, (3 Replies)
Discussion started by: prpkrk
3 Replies
3. AIX
Hello,
I'm very rookie to AIX and attempting to install AIX. I have vio ready on the machine and don't know how to install OS? Inserted Volume 1 DVD into the ROM, don't know what to do next. Searched many forum but cant find the this basic thing. Please let me know how to install AIX on this... (4 Replies)
Discussion started by: pjeedu2247
4 Replies
4. AIX
Hello,
I installed PowerVM IVM Virtual I/O on P-550 but later found out that the machine isn't activated for CoD VET code for virtualization.
So when booted , it goes into OPEN Firmware
I/O Hosting requires a hosting partition boot not permitted exit called
> ok
Panel shows > IO... (3 Replies)
Discussion started by: filosophizer
3 Replies
5. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
6. Linux
Anyone can help me answer the question.
Why does they use Linux on IBM pSeries not AIX.
I can't understand why, cause AIX is the best supporting from IBM pSeries.
Tks you. (3 Replies)
Discussion started by: quan0509
3 Replies
7. AIX
Hello Gurus,
i'm quite new person in AIX world, actually i'm SAP consultant. But due to my job faced with AIX.
Trying to configure new server for installation SAP. We have 4 disks one of them (hdisk3) has VG rootvg. How i can extend rootvg with another disk?
i tried:
# extendvg rootvg hdisk0... (2 Replies)
Discussion started by: sapbcer
2 Replies
8. AIX
Hi All --
I have an old 7028-6C1 which I'm using to learn AIX. The system didn't include a graphics card, so I connected via the serial port and performed a fresh install of AIX 5L V5.3.
Later, I purchased a GXT135P (2849) graphics card, and added it to the system. When I ran diag, I was able... (2 Replies)
Discussion started by: i386tech
2 Replies
9. UNIX for Dummies Questions & Answers
I'm new with UNIX, i have a pseries server from IBM and i need to install AIX 4.3, i never used wyse terminal or AIX, i need help to know how to install it, i have the server and the wyse i get in into the aixterm, over com1 but i don't know wich command use or what to do to install it..... ... (0 Replies)
Discussion started by: Juan-ito
0 Replies
10. AIX
I have been given some pSeries AIX servers to maintain. One of the servers wont come up after a shutdown and the following code is showing on the server:
10118401
How do I look up the error code? (2 Replies)
Discussion started by: dangral
2 Replies
vxbootsetup(1M) vxbootsetup(1M)
NAME
vxbootsetup - set up system boot information on a Veritas Volume Manager disk
SYNOPSIS
/etc/vx/bin/vxbootsetup [-g diskgroup] [medianame ... ]
DESCRIPTION
The vxbootsetup utility configures physical disks so that they can be used to boot the system. Before vxbootsetup is called to configure a
disk, the required volumes, standvol, rootvol and swapvol (and optionally, dumpvol) must be created on the disk. All of these volumes must
be contiguous with only one subdisk.
The -g option may be used to specify the boot disk group.
If no medianame arguments are specified, all disks that contain usable mirrors of the root, swap, /usr and /var volumes are configured to
be bootable.
If medianame arguments are given, only the disks that are associated with the specified disk names are configured to be bootable.
vxbootsetup requires that:
o The root volume must be named rootvol and must have a usage type of root.
o The swap volume must be named swapvol and must have a usage type of swap.
o The volumes containing /usr and /var (if any) must be named usr and var, respectively.
See the chapter "Recovery from Boot Disk Failure" in the Veritas Volume Manager Troubleshooting Guide for detailed information on how the
system boots and how VxVM impacts the system boot process. The vxmirror, vxrootmir, and vxresize utilities call vxbootsetup automatically.
If you use vxassist, or vxmake and vxplex to create mirrors of the root volume on a disk, you must run vxbootsetup explicitly to make the
disk bootable.
ARGUMENTS
medianame
Specifies the disk name (disk media name) of a VM disk that is to be configured as bootable.
SEE ALSO
disksetup(1M), edvtoc(1M), vxassist(1M), vxevac(1M), vxinstall(1M), vxintro(1M), vxmake(1M), vxmirror(1M), vxplex(1M), vxresize(1M),
vxrootmir(1M)
Veritas Volume Manager Troubleshooting Guide
VxVM 5.0.31.1 24 Mar 2008 vxbootsetup(1M)