10 More Discussions You Might Find Interesting
1. AIX
Hi,
when I boot I get an E1DC error code. I've looked it up and it says that this error occurs during the firmware check. But the error is called "Dynamic Console Selection" .
1- Machine stopped at LCD led display = E1DC = CA00E1DC
E1DC Dynamic console selection. (maybe cable or keyboard)... (3 Replies)
Discussion started by: filosophizer
3 Replies
2. AIX
Hi guys,
My company just bought pseries server from ibm,
would like to ask , if first i need to install HMC for creating lpars ?
or first i need to install aix , and then install hmc?
Thx, (3 Replies)
Discussion started by: prpkrk
3 Replies
3. AIX
Hello,
I'm very rookie to AIX and attempting to install AIX. I have vio ready on the machine and don't know how to install OS? Inserted Volume 1 DVD into the ROM, don't know what to do next. Searched many forum but cant find the this basic thing. Please let me know how to install AIX on this... (4 Replies)
Discussion started by: pjeedu2247
4 Replies
4. AIX
Hello,
I installed PowerVM IVM Virtual I/O on P-550 but later found out that the machine isn't activated for CoD VET code for virtualization.
So when booted , it goes into OPEN Firmware
I/O Hosting requires a hosting partition boot not permitted exit called
> ok
Panel shows > IO... (3 Replies)
Discussion started by: filosophizer
3 Replies
5. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
6. Linux
Anyone can help me answer the question.
Why does they use Linux on IBM pSeries not AIX.
I can't understand why, cause AIX is the best supporting from IBM pSeries.
Tks you. (3 Replies)
Discussion started by: quan0509
3 Replies
7. AIX
Hello Gurus,
i'm quite new person in AIX world, actually i'm SAP consultant. But due to my job faced with AIX.
Trying to configure new server for installation SAP. We have 4 disks one of them (hdisk3) has VG rootvg. How i can extend rootvg with another disk?
i tried:
# extendvg rootvg hdisk0... (2 Replies)
Discussion started by: sapbcer
2 Replies
8. AIX
Hi All --
I have an old 7028-6C1 which I'm using to learn AIX. The system didn't include a graphics card, so I connected via the serial port and performed a fresh install of AIX 5L V5.3.
Later, I purchased a GXT135P (2849) graphics card, and added it to the system. When I ran diag, I was able... (2 Replies)
Discussion started by: i386tech
2 Replies
9. UNIX for Dummies Questions & Answers
I'm new with UNIX, i have a pseries server from IBM and i need to install AIX 4.3, i never used wyse terminal or AIX, i need help to know how to install it, i have the server and the wyse i get in into the aixterm, over com1 but i don't know wich command use or what to do to install it..... ... (0 Replies)
Discussion started by: Juan-ito
0 Replies
10. AIX
I have been given some pSeries AIX servers to maintain. One of the servers wont come up after a shutdown and the following code is showing on the server:
10118401
How do I look up the error code? (2 Replies)
Discussion started by: dangral
2 Replies
voldiskadm(8) System Manager's Manual voldiskadm(8)
NAME
voldiskadm - Menu interface for LSM disk administration
SYNOPSIS
/usr/sbin/voldiskadm
DESCRIPTION
The voldiskadm script is an interactive tool that presents a menu of possible operations to the user. When an operation is selected, the
script guides the user through the necessary steps, and prompts for data needed to complete the operation.
The voldiskadm interface is intended mainly for beginning users and for those who prefer a simple method for doing common operations. The
interface uses query-based prompts to gather input, with defaults supplied when possible. Context-sensitive help is available at every
prompt by typing ?. Also, a list option can be used to get information on available target disks for an operation.
For operations that require a device name, one or more names can be specified using a space-separated list. Names in the list can have the
form dskn or rdskn (for an entire disk) or dsknp or rdsknp (for a specific disk partition). Disk names relate directly to device names in
the /dev/disk and /dev/rdisk directories.
The file, /etc/vol/disks.exclude, may be used to exclude disks from use by voldiskadm. Each line of the file specifies the name of a disk
to exclude (for example, dsk5).
The voldiskadm menu includes the following options: Add or initialize one or more disks
This option prompts for one or more disk device addresses. The specified disks can be added to an existing disk group, added to a
new disk group, added to a disk group as spares, or initialized but not added to a disk group (reserved for use as replacement
disks).
After specifying the disks, the user is prompted for a disk group (rootdg by default) and a disk name. If no name is specified, a
default disk name is assigned (diskn for disks in the rootdg disk group and diskgroupn for disks in other disk groups).
The disks are then checked to ensure that there is no information already on them. If there is, the user is given the option of
encapsulating the disks. Encapsulate one or more disks
This option prompts for one or more disk addresses. It then calls volencap to encapsulate the specified partitions. Remove a disk
This option prompts for a disk, by disk media name. The disk is checked to ensure that no subdisks reside on the disk. If the disk
is in use, the operation fails with a recommendation to first move all volumes off the disk. If this disk is the last disk in a
disk group, the user is prompted for whether the disk group should be removed from the system, as well.
The operation proceeds by calling voldg rmdisk to remove the disk from its disk group. If this is the last disk in its disk group,
voldg deport is used, instead, to remove the disk group from use. Remove a disk for replacement
This option prompts for a disk, by disk media name. The disk is checked for volumes that would lose all mirrors as a result of the
operation. If such volumes exist, they are listed and the user is prompted to ensure that the operation should proceed.
The operation proceeds by calling voldg -k rmdisk to dissociate the media record from the physical disk. If some formatted disks
are under LSM control but not assigned to a disk group, the user is prompted for whether one of these disks should be used as a
replacement. Replace a failed or removed disk
This option prompts for a disk media name. The named media record must be dissociated from a disk. If the media record is not in
the removed state, unused disks are scanned for matching disk IDs. If a disk with a matching disk ID is found, the user is prompted
for whether that disk should be reattached.
If a matching disk is not used, the user is prompted for a new disk, by device name. If the named replacement disk has a valid disk
header, but is not allocated to a disk group, the user is prompted for whether the disk should be reinitialized. If the named
replacement disk is listed as allocated to a disk group or to another host, the user is prompted to ensure that the operation should
proceed.
If the device is to be initialized, a new disk label is written to the disk to reflect its private and public regions.
Given an initialized disk, the operation proceeds by replacing the disk in a disk group with voldg -k adddisk. Mirror volumes on a
disk
This option prompts for a disk, by disk media name. It then prompts for a destination disk within the same disk group, also by disk
media name. Specifying no destination disks indicates that any disk is suitable. The operation proceeds by calling volmirror to
mirror the volumes.
Mirroring volumes from the boot disk will produce a disk that can be used as an alternate boot disk. This is done by calling the
volrootmir command. Move volumes from a disk
This option prompts for a disk, by disk media name. It then prompts for a possible list of destination disks, also by disk media
name. Specifying no destination disks indicates that any disk is suitable. The operation proceeds by calling volevac to move sub-
disks off the disk. Enable access to (import) a disk group
This option prompts for a disk, by device address. The operation proceeds by calling voldg import to import the disk group stored
on that disk. Disable access to (deport) a disk group
This option prompts for a disk group name. The prompt display lists alternate disk groups and the disks (media name and access
name) that they contain. The operation proceeds by calling voldg deport. Enable (online) a disk device
This option prompts for a disk device. The prompt display allows for a display of disks on the system. The operation only func-
tions for disks currently in an offline state. It then proceeds to make the disk accessible. Disable (offline) a disk device
This option prompts for a disk device. The prompt display allows for a display of disks on the system. The operation only func-
tions for disks currently in an online state but not part of any disk group. It then proceeds to mark the disk as offline such that
the Logical Storage Manager makes no further attempt at accessing the disk. Mark a disk as a spare for a disk group
This option sets up a disk to be used as a spare device for its disk group. A spare disk can be used to automatically replace a disk
that has failed. No space can be used on a disk that is marked as a spare. Turn off the spare flag for a disk
This option removes a disk from those that can be used as a spare and returns its space to the general pool of available space.
Recover plexes and volumes after replacement
This operation performs plex attachment, RAID-5 subdisk recovery, and resynchronize operations for the named volumes, or for volumes
residing on the named disks (media name). If no media name or volume operands are specified, the operation applies to all volumes
(or to all volumes in the specified disk group).
ERRORS
See the voldiskadd(8) reference page for a description of errors related to the initialization operation.
FILES
A list of disks to exclude from use by voldiskadm.
SEE ALSO
disklabel(8), volintro(8), voldg(8), voldisk(8), voldiskadd(8), voldisksetup(8), volrootmir(8)
voldiskadm(8)