10 More Discussions You Might Find Interesting
1. UNIX Desktop Questions & Answers
It was happened to close my laptop without proper shutdown due to power failure with USB device connected to it. (removed the USB after shut down)
After this incident, I was not able to boot my suse linux OS.
Initial study reveals that the device is not unmounted properly and shows... (2 Replies)
Discussion started by: Prabhu V
2. UNIX for Dummies Questions & Answers
I am a newbie to Suse linux and was trying to configure internet on my 11.4 suse linux system . I followed a post according to which i uninstalled my NetworkManger library . Later i realised that the real reason for wireless not working on my system was that my wireless driver firmware was... (0 Replies)
Discussion started by: ihatetoregister
Previously I had both opensuse 11.3 and Windows XP SP2 on my PC, there was no problem at all.I was able to access all documents in Windows from opensuse.
Now when I wanted to install solaris 10 on the same machine there were 2 problems ...
1. Windows is not accessible from solaris... (3 Replies)
Discussion started by: M.Choudhury
4. Filesystems, Disks and Memory
I setup a RAID 5 with 5 drives, one failed, hardware failure so I physically removed it from the raid after powering the machine off then powered it back on and my raid was still good but no 5th drive. I built a 5th drive from scratch and added it in the raid thinking the raid would go into... (0 Replies)
Discussion started by: lacakid
i am trying to find whether the given name is file or a directory
dirp = opendir(dirname);
direntp = readdir(dirp);
if(direntp->d_type & DT_DIR)
printf("\n is a dirctory");
//dir_or_file = Mtrue;
printf("\n not a directory");
it always... (9 Replies)
Discussion started by: vin_pll
Am very new to Linux OS.. This is my first experience with Linux.
I have installed linux suse 10 in my laptop.it was working fine.. suddenly after 3 days,(i was changing some options of the already installed linux) when i login, i am getting only command interface and GUI is not... (2 Replies)
Discussion started by: mac4rfree
7. Filesystems, Disks and Memory
Working on Oracle v220.127.116.11.0 with OS as Suse v8.0 Linux.
I had created LVM,linked raw devices to LVM as below:
# for binding raw devices
raw /dev/raw/raw1 /dev/oracle/sam_raw_system_251m
raw /dev/raw/raw2 /dev/oracle/sam_raw_users_26m
raw /dev/raw/raw3... (2 Replies)
Discussion started by: Amitstora
I setup SUSE Linux 10.
I downloaded from SUSE website. A DVD version.
But I have a problem:
Please click to see the screen shots
Shot 1: (Problem is here, with Software)
Shot 3:... (1 Reply)
Discussion started by: HASSELBLAD
9. UNIX for Dummies Questions & Answers
i got a NV11 geForce2 100/200 and suse 9.0 pro boot the kernal but then the screen
goes blank and nothing else can't install suse 9.0 pro and grabs for this problem
x will not come up at all
just the boot screen with rez and so on but once i tell it to install thats i have a nec multisync... (6 Replies)
Discussion started by: 3bumbs plumming
10. UNIX for Dummies Questions & Answers
i have just installed suse 8.1 on a third computer which has an Asus p4s8x with onboard NIC and sound. now, on install suse detected everything automatically with no probelm, however upon reboot the sound failed to load as well as the network card. /dev/eth* doesnt exist. i looked in the bios and... (2 Replies)
Discussion started by: norsk hedensk
SMPPPD(8) SMPPPD SMPPPD(8)
smpppd - SuSE Meta PPP Daemon
smpppd is a daemon that controls several internet connections.
Use a frontend like cinternet , qinternet or kinternet to control the connections and retrieve status informations. Those frontends can
also run on different hosts.
The configuration of the dialup connections is done by YaST2 but there are some additional options available in the file /etc/smpppd.conf.
smpppd is not intended for direct use. Use rcsmpppd instead.
These options are recognized by smpppd.
Detach from the controlling terminal. This is the default.
Don't detach from the controlling terminal.
Turn on debugging.
Show program version and exit.
--help Show help information and exit.
ISDN support is poor.
SIGHUP Reload the configuration.
Configuration files for the interfaces.
Configuration files for the providers.
Socket to communicate with local frontends.
Sockets to communicate with backends.
kinternet, qinternet, accounting(1), cinternet(1), wvdial(1), smpppd.conf(5), pppd(8), smpppd-ifcfg(8).
Arvin Schnell <firstname.lastname@example.org>
SuSE September 2003 SMPPPD(8)