10 More Discussions You Might Find Interesting
1. IP Networking
I have built a new linux server, via a iLo connection.
and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty.
Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies
2. SCO
Hi all,
n00b here. We currently have 3 SCO 5.0.5 machines in our network that run a mission management system.
Our internal network was always a 10.0.0.0 network and the machines worked fine.
Our company is going through a network upgrade for VoIP and some of our departments are now on... (5 Replies)
Discussion started by: gibson_hg
5 Replies
3. Solaris
Hi,
I need help to add new route:
10.252.0.138, GW 10.252.0.129 to e1000g1
and
10.252.0.10, GW 10.252.0.1 to e1000g2
tnx (4 Replies)
Discussion started by: mehrdad68
4 Replies
4. Solaris
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies
5. IP Networking
I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system.
The ip i am trying to get to is 172.16.4.48
I need to get to it via the hme1 interface.
The vpn gateway has this ip 172.30.50.1
I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
5 Replies
6. AIX
Hi,
IBM Server with AIX 5.2. I have already added a static route for a whole network but everyday some automatic routes to hosts adds up in route table of this server, some of which invalid routes that stops communication of server to that network. If these invalid routes are removed from route... (0 Replies)
Discussion started by: system-admin
0 Replies
7. SCO
Hi,
I add following routes manually each time system reboots:
#route add 192.168.1.0 -gateway 192.168.0.90
#route add 192.168.200.0 -gateway 192.168.0.200
Is there any way in SCO 7.1.1 to automate this route add process? i.e. each time system reboots, it automatically adds these routes in... (1 Reply)
Discussion started by: tayyabq8
1 Replies
8. IP Networking
I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0.
My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network.
My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies
9. AIX
Hello ,
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies
10. UNIX for Dummies Questions & Answers
I need some help adding routes in sco.
I am using SCO Openserver 5.0.4.
Basically I have 2 gateways here. The first is 10.15.1.1 and allows me access to the rest of the computers in the office and in other offices.
The other gateway is 10.15.10.2 and is the sonicwall that will allow access... (3 Replies)
Discussion started by: cstovall
3 Replies