10 More Discussions You Might Find Interesting
1. Solaris
hello all
i have an issue about a solaris V440 cpu, im logged in the Ok prompt i can't disable a CPU3, i can't see it in dev list, i see only the cpu3-bank0 to cpu-bank4
please help me to disable it
thank youuu (3 Replies)
Discussion started by: walidadam
3 Replies
2. Solaris
hi,
just installed solaris 11.1 (11.1.9.5.1) on a sun7410 ZFSSA (x4440 + j4400), but when I enable multipathing with "stmsboot -e", only the 1TB SATA drives inside the j4400 are configured as multipathed vhci / mpxio devices, but the logzillas / ZeusIOPS drives are skipped. the server is... (0 Replies)
Discussion started by: pressy
0 Replies
3. Solaris
I've new installed Solaris 11 on Sparc T4-1.
I'd like to disable IPv6 but with no luck.
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
net0: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 2
inet... (6 Replies)
Discussion started by: samer.odeh
6 Replies
4. Solaris
Hi
Is there anyway to disable all logs/logging (lastlog, sulog, messages etc.) in Solaris 9&10? I know this is not recommended but i just want to know if this is possible.
TIA
Reddy (8 Replies)
Discussion started by: reddyr
8 Replies
5. Solaris
Hai
we using emc storage which is conneted to M5000 through san switch.
we asign 13 luns but in server it is showing 22 luns.
i enable the solaris multipathing (MPxIO)
#more /kernel/drv/fp.conf in that file
MPxio-disable=no
#mpathadm list lu
it shows ... (2 Replies)
Discussion started by: joshmani
2 Replies
6. Solaris
Hi,
I saw your post on the forums about how to setup IP multipathing. I wanted your help on the below situation .
I have 2 servers A and B . Now they should be connected to 2 network switches . S1 and S2.
Now is it possible to have IP Multipathing on each of the servers as follows ?
... (0 Replies)
Discussion started by: maadhuu
0 Replies
7. Solaris
Hello All,
I work for a Health care company at a local trauma hospital. I maintain a Picture Archiving and Communication System (PAC's). Basically, any medical images (X-Ray, CT, MRI, Mammo, etc) are stored digitally on the servers for viewing and dictation from diagnostic stations. I took over... (10 Replies)
Discussion started by: mainegeek
10 Replies
8. Solaris
I have solaris 10 sparc. I installed a Qlogic hba card.
This card is connected on a brocade switch and the brocade is connected on 2 different controllers on a Hitachi disk bay.
I formated 2 luns. On my solaris system, i have 4 disk.
How to configure solaris 10 to fix the dual disk view.
... (4 Replies)
Discussion started by: simquest
4 Replies
9. Solaris
All -
would you please some one help me to disable telnet on Solaris?
/etc/inetd.conf
Thanks :confused: (11 Replies)
Discussion started by: March_2007
11 Replies
10. IP Networking
I've setup Solaris IP Multipathing under Solaris whenever the hardware to do so was available. I find it amazing though that so few places I've worked at don't use it until I arrive. I wanted to find out if I'm running into all the exceptions, or is it really not being used? ... (3 Replies)
Discussion started by: kduffin
3 Replies