How to identifying the network card ?

10 More Discussions You Might Find Interesting

1. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101...

2. Hardware

Identifying Network Ports

OK, so I have a real dumb question, but I am desperate for an answer. If my Sun machine shows the following out put. root@xxxx:/# egrep network /etc/path_to_inst "/pci@1f,0/pci@1,1/network@c,1" 0 "eri" "/pci@1f,0/pci@1,1/network@5,1" 1 "eri" Does that indicate that there is one eri...

3. UNIX for Dummies Questions & Answers

How to install a network card

Hey guys, Sorry, this question might look stupid but I have no idea how to install a network card. My server is a Dell PowerEdge T105 with Debian 5.0 Lenny. My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express. I've plugged the card innside my server and I can see...

4. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated.

5. UNIX for Dummies Questions & Answers

Network card and internet

Hi!. I have problems installing my network card under ther redhat kernel. First i tryed my integrated intel pro set 10/100 then my d-link 530tx Pci but none of them seems to be found. also i huse my network card to connect to the net trough PPPOE where i need to type my username and...

6. UNIX for Advanced & Expert Users

network card problem

hi, everyone: alpha 600 au true64 Unix 4.0f my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages. "tu0 :transmit FIFO underflow:threshold raised to :256 byte��link up...

7. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of...

8. IP Networking

Network Card with SGI

The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out > link ok < when i connected > But...

9. UNIX for Dummies Questions & Answers

Installing network card

1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface, 2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out.

10. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the...

LEARN ABOUT REDHAT

ifport

IFPORT(8)						      System Manager's Manual							 IFPORT(8)

NAME

       ifport - select the transceiver type for a network interface

SYNOPSIS

       ifport interface [auto|10baseT|10base2|aui|100baseT|##]

DESCRIPTION

       Ifport  sets  the  transceiver type for the specified network interface, for drivers that support multiple transceiver types.  If a type is
       not specified on the command line, then the current type is displayed.  The type can be specified either numerically or	by  keyword.   The
       five  standard  transceiver  types (auto, 10baseT, 10base2, aui, and 100baseT) correspond to codes 0 to 3, for all the Linux PCMCIA network
       drivers.  The keyword match is case insensitive.

       The network drivers may not reconfigure a card for a new transceiver type if the interface is already open.  It is best	to  invoke  ifport
       prior to configuring the interface with ifconfig to ensure that the new setting takes effect immediately.

       This  utility  only  works  with  a  limited set of 16-bit PC Card drivers: 3c589_cs, nmclan_cs, pcnet_cs, smc91c92_cs, and xirc2ps_cs.	If
       invoked for other drivers, ifport may report bogus transceiver settings, or report ``Operation not supported''.

DIAGNOSTICS

       ioctl: Operation not supported
	      Indicates that this network device does not support manual transceiver selection.  There may be only one transceiver option, or  the
	      device may always autodetect the appropriate transceiver.

AUTHOR

       David Hinds - dahinds@users.sourceforge.net

SEE ALSO

       ifconfig(8).

pcmcia-cs							2000/06/12 21:24:48							 IFPORT(8)

Solaris