10 More Discussions You Might Find Interesting
1. Red Hat
Dear All ,
While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card.
Pl find the below alert.
Network Interface Card performance for NIC:eth1 has exceeded Major threshold.
Bytes sent and received per second (Average)= 105540.303101... (6 Replies)
Discussion started by: jegaraman
6 Replies
2. Hardware
OK, so I have a real dumb question, but I am desperate for an answer.
If my Sun machine shows the following out put.
root@xxxx:/# egrep network /etc/path_to_inst
"/pci@1f,0/pci@1,1/network@c,1" 0 "eri"
"/pci@1f,0/pci@1,1/network@5,1" 1 "eri"
Does that indicate that there is one eri... (2 Replies)
Discussion started by: Tirmazi
2 Replies
3. UNIX for Dummies Questions & Answers
Hey guys,
Sorry, this question might look stupid but I have no idea how to install a network card.
My server is a Dell PowerEdge T105 with Debian 5.0 Lenny.
My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express.
I've plugged the card innside my server and I can see... (2 Replies)
Discussion started by: chebarbudo
2 Replies
4. UNIX for Dummies Questions & Answers
I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink?
Any advice would be appreciated. (6 Replies)
Discussion started by: mojoman
6 Replies
5. UNIX for Dummies Questions & Answers
Hi!.
I have problems installing my network card under
ther redhat kernel.
First i tryed my integrated intel pro set 10/100
then my d-link 530tx Pci but none of them seems to
be found.
also i huse my network card to connect to the net
trough PPPOE where i need to type my username and... (3 Replies)
Discussion started by: Gibbler
3 Replies
6. UNIX for Advanced & Expert Users
hi, everyone:
alpha 600 au true64 Unix 4.0f
my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages.
"tu0 :transmit FIFO underflow:threshold raised to :256 byteŁ¬link up... (1 Reply)
Discussion started by: q30
1 Replies
7. UNIX for Advanced & Expert Users
I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies
8. IP Networking
The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out >
link ok < when i connected >
But... (0 Replies)
Discussion started by: DPAI
0 Replies
9. UNIX for Dummies Questions & Answers
1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface,
2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out. (1 Reply)
Discussion started by: gops
1 Replies
10. IP Networking
I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies