Jumpstart Issues Solaris 10


 
Thread Tools Search this Thread
Operating Systems Solaris Jumpstart Issues Solaris 10
# 1  
Old 12-05-2008
Jumpstart Issues Solaris 10

I'm trying to jumpstart my remote server. My /etc/hosts and /etc/ethers files have the correct data. Keep getting the following message at the ok prompt
after running a boot net - install

Link hasn't comeup yet

Ran a test-net and got the following message.

Link is -- down


When bringing up the host server that Im trying to jumpstart, the network connection is fine both ways. Can anyone provide any insight to this?
# 2  
Old 12-05-2008
have you run the script "add_install_client" to setup /etc/bootparams file?
# 3  
Old 12-05-2008
Are you running a direct 1-cable connection between the server and client or do you route through a switch or other network device?
# 4  
Old 12-05-2008
The two servers are networked together through switches. The bootparms file has all the correct information about the server to be jumpstarted.
# 5  
Old 12-05-2008
do you have more than one network interfaces? maybe you try to boot from the wrong nic... test this with:

Code:
ok show-nets
ok cd /path/to/your/nic
ok .properties

and check the mac you find with .properties with the one in your ethers file. also check the obp setting for local-mac is set to "true".
# 6  
Old 12-05-2008
This might be a duplex issue. If the host is not setting its speed and duplex correctly at the OK prompt then we'd see these link down issues. I recommend allowing auto-negotiate at the switch.
The best way to confirm or rule-out this theory is to try a jumpstart with the two servers directly connected.
# 7  
Old 12-05-2008
Quote:
networked together through switches
are these on the same network segment? its not clear if they are or not.
Login or Register to Ask a Question

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. Solaris

Solaris 10 JumpStart Server

Hello, Can anyone share a good online article/tutorial on how to properly set up JumpStart server for Solaris 10? Thanks, Regards. (3 Replies)
Discussion started by: NewSolarisSquad
3 Replies

2. Solaris

Jumpstart Solaris 10

I have a laptop and need to build an Oracle Linux kickstart server and a Solaris Jumpstart server that can build sparc and x86 systems. Is the best way to create a dual boot from grub for Oracle Linux and Solaris x86? Can the Oracle Kickstart be used as a Jumpstart to build both Solaris 10... (2 Replies)
Discussion started by: Gian
2 Replies

3. Solaris

Jumpstart Issues With T5220

I'm trying to use a V210 (sun4u) configured as a jumpstart server to flash install a number of T5220's (sunv4). The Facts: V210 - Solaris 10 (September 2010 Release / not patched) T5220's - Archive's created using prior (unknown) version of solaris 10. Flar -i <archive name> shows the... (6 Replies)
Discussion started by: Celtic_Monkey
6 Replies

4. Solaris

Issue after jumpstart with Solaris 10 u7

I am performing this installation on a Sun T5220. There is an aftermarket Adaptec StorageTek raid controller card installed. I have created the raid array, and it is referred to as c1t0d0. Here is the profile I have created: install_type initial_install system_type server cluster SUNWCXall... (4 Replies)
Discussion started by: msarro
4 Replies

5. Solaris

Jumpstart Solaris 10

Hello everyone, I tried to install solaris 10 using the command # boot net - install. I take the image correctly but when you start installing the Operating system installation takes a long (4 hours I have left and not advancing but not send me any errors), it can be seen from the following: ... (7 Replies)
Discussion started by: yflores
7 Replies

6. Solaris

Jumpstart issues, help please.

1.I wish to perform a Jumpstart installation, the client being Ultra 5 Sparc and jumpstart Server being ultra 20 AMD system. 2.I think i have done all the procedures right, like putting the mac address of Sparc 1 to /etc/ethers, creating sysidcfg file, and profile file: 3.When I issued the boot... (7 Replies)
Discussion started by: saagar
7 Replies

7. Solaris

Jumpstart Issues

Hi all, I'm having an issue with jumpstart that I haven't seen before. After booting the server and selecting F12 to boot it from the network it finds the jumpstart profile that has been set up for it and proceeds with the build until I get the following error: SunOS Release 5.10 Version... (4 Replies)
Discussion started by: Chains
4 Replies

8. Solaris

Jumpstart solaris

Hi all , I am trying to jumpstart ( webstart) solaris 9 on E2900 ( client) using the DVD of a V440 server ( jumstart server). I did the setup for the V440 as follows : cleaning up preexisting install client "XXXXXXX" removing XXXXXXXfrom bootparams removing /etc/bootparams, since it is... (14 Replies)
Discussion started by: ppass
14 Replies

9. Solaris

jumpstart Solaris 10 on Solaris 9 server

I just built a jumpstart server on a Solaris 9 sun box and have had no problems jumpstarting other sol9 boxes using the custom rules. I've also copied a Solaris 10 image onto that same solaris 9 server and have had problems loading Solaris 10. These boxes will go directly to the manual OS install... (5 Replies)
Discussion started by: salty
5 Replies
Login or Register to Ask a Question