10 More Discussions You Might Find Interesting
1. Red Hat
Hi folks,
I am trying to configure Apache webserver and also a virtual host inside this webserver.
For Global server config: /var/www/html/index.html
For virtual host config: /var/www/virtual/index.html
Both client10 & www10 are pointing to 192.168.122.10 IP address.
BUT, MY... (1 Reply)
Discussion started by: freebird8z
1 Replies
2. Solaris
Dear All,
After configuring IPMP in 2 fresh Servers (T5520 and T2000) I can't login in any of them using SSH, I can login by serial console then I had to enable Telnet to access.
IPMP works fine.
This is the error in /var/adm/messages:
sshd: Failed password for lvalle from 172.28.12.95 port... (0 Replies)
Discussion started by: Luis Valle
0 Replies
3. Solaris
Can any one please explain me the concept behind IPMP in solaris clustering.Basic explanation would be really appreciated...
Thanks in Advance
vks (2 Replies)
Discussion started by: vks47
2 Replies
4. Shell Programming and Scripting
Hi I am new to shell scripting. There is a requirement to write a shell script to meet follwing needs.Prompt reply shall be highly appreciated.
script that will compare two config files and produce 2 outputs - actual config file and a report indicating changes made.
OS :Susi linux ver 10.3.
... (4 Replies)
Discussion started by: muraliinfy04
4 Replies
5. Solaris
Hi all
i had two interface
ce0 and ce5
but when i run the ifconfig, it show me alot of extra virtual interface, may i know how to remove it?
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
ce0:... (2 Replies)
Discussion started by: SmartAntz
2 Replies
6. Solaris
Please tell me how to configure IPMP in vmware
what is the basic working concept of IPMP.
please help me (1 Reply)
Discussion started by: sijocg
1 Replies
7. Shell Programming and Scripting
Hi,
I want to use a config file as the base file and parse over the values of country and city parameters in the config file and generate separate config files as explained below.
I will be using the config file as mentioned below:
(config.txt)
country:a,b
city:1,2
type:b1... (1 Reply)
Discussion started by: clazzic
1 Replies
8. Solaris
Probe-based IPMP active - active
Probe-based IPMP active - passive
Link-based only active -standby
????
What are differences between
Probe-based IPMP active - passive anddd
Link-based only active -standby
???!!!
For example in active active probe-based IPMP there are
lets... (6 Replies)
Discussion started by: samar
6 Replies
9. Solaris
Hi All,
Kindly help me in configuring IPMP or guid me to some link, tried goggling however no luck.
Thanks in anticipation (1 Reply)
Discussion started by: kumarmani
1 Replies
10. Solaris
Hi
I am setting up a test server for actual 2 node servers which will be behind load balancer. I will not be using sun cluster at all. The test machine is installed with solaris 10.
I am not sure how to setup a test env of 2 nodes on only 1 node..may be creating 2 zones on test server will... (8 Replies)
Discussion started by: upengan78
8 Replies
unbound-checkconf(8) unbound 1.4.17 unbound-checkconf(8)
NAME
unbound-checkconf - Check unbound configuration file for errors.
SYNOPSIS
unbound-checkconf [-h] [-o option] [cfgfile]
DESCRIPTION
Unbound-checkconf checks the configuration file for the unbound(8) DNS resolver for syntax and other errors. The config file syntax is
described in unbound.conf(5).
The available options are:
-h Show the version and commandline option help.
-o option
If given, after checking the config file the value of this option is printed to stdout. For "" (disabled) options an empty line is
printed.
cfgfile
The config file to read with settings for unbound. It is checked. If omitted, the config file at the default location is checked.
EXIT CODE
The unbound-checkconf program exits with status code 1 on error, 0 for a correct config file.
FILES
/etc/unbound/unbound.conf
unbound configuration file.
SEE ALSO
unbound.conf(5), unbound(8).
NLnet Labs May 24, 2012 unbound-checkconf(8)