10 More Discussions You Might Find Interesting
1. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
2. Solaris
Dear All,
I need your help. I have server like this
SunOS 5.10 Generic_141444-09 sun4u sparc SUNW,Sun-Fire-V890
with messages like this...
Oct 10 17:07:52 iscsi: NOTICE: unrecognized ioctl 0x403
Oct 10 17:07:52 scsi: WARNING: /pseudo/fcp@0 (fcp0):
Oct 10 17:07:52 Invalid... (4 Replies)
Discussion started by: mbah_jiman
4 Replies
3. Solaris
Hello,
In Solaris 10 I can use fcinfo to find what speed the hba ports are running at, am I able to find this out using Solaris 9? I have tried a few variations on luxadm but cant find anything relevant.
Thanks. (1 Reply)
Discussion started by: Actuator
1 Replies
4. Solaris
Hi,
I have been given the task of configuring new SAN disks on two Solaris 10 boxes. The boxes in question have two dual channel QLogic FC cards, one port on each goes to an existing HDS SAN and are managed via HDLM. The intention is to connect the two free ports to a NetApp SAN and then... (12 Replies)
Discussion started by: trickydicky
12 Replies
5. Solaris
Hi all,
I managed to get WWN port number & node from trying on
luxadm -e port
luxadm -e dump_map <device>
I wanted to ask how can i get additional information such as company name, size etc of the HBA? Is it possible to get it through command? Thanks. (3 Replies)
Discussion started by: beginningDBA
3 Replies
6. Solaris
Hi,
I have a HBA that is currently offline for some unknown reason. The device shows up in the prtdiag -v stating it is okay. How can I bring this back online? It was working okay until recently. It is currently connected to the SAN. Details below.
# fcinfo hba-port
HBA Port WWN:... (7 Replies)
Discussion started by: sparcman
7 Replies
7. Filesystems, Disks and Memory
Hope I'm in the right place. I'm in the process of zoning HBA's to my new library environment. Is there a "rule of thumb" for the number of physical tape drives that you zone to an HBA? I don't want to run the risk of overloading an HBA. Any information would be greatly appreciated. Thanks. (2 Replies)
Discussion started by: jwholey
2 Replies
8. UNIX for Advanced & Expert Users
hello, i have a dell Poweredge 2950 ( Server ) and an IBM storage device DS 3000 family ( Storage ) . I am supposed to link the IBM storage device to the Dell Poweredge via "Emulex 4Gb Fibre Channel Host Bus Adapter".
I have put the addapter card in my server and connected it to the storage.... (3 Replies)
Discussion started by: nux007
3 Replies
9. AIX
Hi All,
SUN emulex HBA card has been installed on P520 box.
When i run the cfgmgr i am getting the following message.
lpar2#cfgmgr
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies
10. Solaris
Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies
