Login or Register to Ask a Question and Join Our Community


Solaris

prtvtoc command

Login to Discuss or Reply to this Discussion in Our Community

 
Thread Tools Search this Thread
Operating Systems Solaris prtvtoc command
# 1  
Old 07-14-2008
prtvtoc command
If i have diks layout like below

0 root wm 0 - 634 471.29MB (635/0/0)
965200
1 var wm 635 - 2014 1.00GB (1380/0/0)
2097600
2 backup wm 0 - 2732 1.98GB (2733/0/0)
4154160
3 swap wu 2015 - 2704 512.11MB (690/0/0)
1048800
4 unassigned wm 2705 - 2718 10.39MB (14/0/0)
21280
5 unassigned wm 2719 - 2732 10.39MB (14/0/0)
21280
6 unassigned wm 0 0 (0/0/0)
0
7 unassigned wm 0 0 (0/0/0)
0



And i Want to make disk cloning.

First command is by prtvtoc.

What slice that i have to point in using prtvtoc ?


Regards,

tpx
# 2  
Old 07-14-2008
If you want to copy the partition table to another disk, perform
prtvtoc /dev/rdsk/cxtxdxs2 | fmthard -s - /dev/rdsk/cxtxdxs2
1st controller, target and disk should be the source and the 2nd cxtxdxs2 should be your dest disk.
Then newfs the slices accordingly.
After that, you can use ufsdump to copy the data into the relevant partitons.Smilie
Login or Register to Ask a Question

Previous Thread | Next Thread

10 More Discussions You Might Find Interesting

1. UNIX for Beginners Questions & Answers

Another one line command where I'd like to determine if Ubuntu or Red Hat when running command

Hello Forum, I'm making very good progress on my report thanks to the very helpful people on this forum. I've been able to successfully create my report for my Red Hat servers. But I do have a few ubuntu servers in the mix and I'd like to capture some data from them when an ssh connection is... (8 Replies)
Discussion started by: greavette
8 Replies

2. Solaris

Copied prtvtoc to original disk

Hi, It is Solaris-10 with ZFS. c0t1d0 is original disk. c0t0d0 was faulty disk, which was replaced with new one and by mistake somebody ran opposite command # prtvtoc /dev/rdsk/c0t0d0s0 | fmthard -s - /dev/rdsk/c0t1d0s0 Now rpool is in suspended state. Right now server is up, but allowing ssh... (6 Replies)
Discussion started by: solaris_1977
6 Replies

3. Solaris

Prtvtoc not working

Hi, I am trying to mirror a disk (which was already mirror and after breaking it, doing it again). This is root disk and in control of veritas. Somehow, slice information is not coming correctly on this. Can somebody give some pointer to fix it ? root@tdrp091:/root# prtvtoc /dev/rdsk/c3t0d0s2 |... (6 Replies)
Discussion started by: solaris_1977
6 Replies

4. UNIX for Dummies Questions & Answers

passing command output from one command to the next command in cshell

HI Guys, I hope you are well. I am trying to write a script that gets executed every time i open a shell (cshell). I have two questions about that 1) I need to enter these commands $ echo $DISPLAY $ setenv $DISPLAY output_of_echo_$display_command How can i write a... (2 Replies)
Discussion started by: kaaliakahn
2 Replies

5. UNIX for Advanced & Expert Users

unix command : how to insert text at the cursor location via command line?

Hi, Well my title isn't very clear I think. So to understand my goal: I have a script "test1" #!/bin/bash xvkbd -text blabla with xbindkeys, I bind F5 key in order it runs my test1 script So when I press F5, test1 runs. I'm under Emacs/Vi and I press F5 in order to have "blabla" be... (0 Replies)
Discussion started by: xib.be
0 Replies

6. Shell Programming and Scripting

Need help! command working ok when executed in command line, but fails when run inside a script!

Hi everyone, when executing this command in unix: echo "WM7 Fatal Alerts:", $(cat query1.txt) > a.csvIt works fine, but running this command in a shell script gives an error saying that there's a syntax error. here is content of my script: tdbsrvr$ vi hc.sh "hc.sh" 22 lines, 509... (4 Replies)
Discussion started by: 4dirk1
4 Replies

7. AIX

AIX:Command to get netaddress/subnet address command in IPv4/IP6

AIX:Command to get netaddress/subnet address command in IPv4/IP6 Can anybody help us with a command to retrieve netaddress/subnet address command in IPv4/IP6 on aix machine. net/subnet address is in the format 172.16.212.0(signifies all 255 machines in an IPv4 network) (2 Replies)
Discussion started by: rookie8278
2 Replies

8. Solaris

fmthard showing error with prtvtoc

Hi all, I am trying to use the disk for mirror where in the mirror disk is of 160 gb and the rootdisk is of 80 gb. when i am trying to write the vtoc i am getting below error i tried the below command #prtvtoc /dev/rdsk/c0t0d0s0 |fmthard -s -/dev/rdsk/c0t2d0s0 and got below ... (26 Replies)
Discussion started by: kumarmani
26 Replies

9. Solaris

Output from prtvtoc

Hi All, when i run the command prtvtoc the output shows 38309 cylinders 38307 accessible cylinders as per my undertanding the 1st cylinder is used for storing the vtoc , how about the second cylinder ? where its used and for what purpose? Thanks (9 Replies)
Discussion started by: kumarmani
9 Replies

10. SuSE

inconsistent ls command display at the command prompt & running as a cron job

Sir, I using the following commands in a file (part of a bigger script): #!/bin/bash cd /opt/oracle/bin ls -lt | tail -1 | awk '{print $6}' >> /tmp/ramb.out If I run this from the command prompt the result is: 2007-05-16 if I run it as a cron job then... (5 Replies)
Discussion started by: rajranibl
5 Replies
Login or Register to Ask a Question