so there is good and bad news. i switched to tera term and got output. basically saw the lom> prompt and when i powered on it posted with the banner. however, it fails (as expected on loading anything) and goes to the ok prompt. the bad news. i can't issue any input. any ideas on why that might be?
start the console session with the option "-f" to get write access to the console. otherwise you are in "view" mode only...
duke - i would love to do that but again, i can't give any input.
output as follows from lom:
Code:
LOMlite starting up.
CPU type: H8/3437S, mode 3
Ram-test: 2048 bytes OK
Initialising i2c bus: OK
Searching for EEPROMs: 50(cfg)
I2c eeprom @50: OK
i2c bus speed code 01... OK
Probing for lm80s: 28
Initialising lm80 @28: OK
Probing for lm75s: none
System functions: PSUs fans breakers rails gpio temps host CLI ebus clock
LOMlite console
lom>
LOM event: +0h0m0s LOM booted
lom>
LOM event: +0h0m2s host power on
ü
Netra T1 200 (UltraSPARC-IIe 500MHz), No Keyboard
OpenBoot 4.0, 1024 MB memory installed, Serial #16687876.
Ethernet address 8:0:20:fe:a3:4, Host ID: 80fea304.
Boot device: disk File and args:
The file just loaded does not appear to be executable.
ok
i know what you are going to say next. what about the below:
Code:
Netra T1 200 (UltraSPARC-IIe 500MHz), No Keyboard
well... thats were i'm lost. can't figure out why my keyboard is not registering. i clearly have one. does the netra t1 need a sun keyboard?
pupp - o.k. then the "no keyboard" output is right. only if a keyboard is directly attached this message disapear.
i've no other idea why you can not type... but maybe you've to check the cable as mentioned above. usb -> serial -> lom is sometimes pain in the ...!
what happens if you use the serial port b on the netra? maybe it's worth a try...
Hi Guys,
Could someone please share the dvd/cd that came with server Netra x4200 M2 since it is not more available in Oracle site? Or do you know where I can get that?
Thanks! (4 Replies)
Hello all,
I recently powered on my Netra AX1105 server only to be greeted with the following error message. I am not sure what to do here,
I cant fun fsck on OK prompt.. did ok>boot -r and now it keeps booting from net, then I run ok>boot disk then outputs the following message... and keeps... (3 Replies)
I recently required some Sun Oracle Netra T5220s. I do not have much knowledge of Sun products.
The units do not have video cards or hard drives. How can I tell/go about figuring out what clock speed and how many cores the processor is?
They are all outfitted with 32GB of memory. Two are... (11 Replies)
As the title suggests, I'm trying to install a second drive (really want an OS mirror) on a Sun Netra X1.
I've taken the spacer out, and had a go at with the drill-press so now I have a nice HDD tray. Have installed an IDE drive in the tray, plugged in the power and data cables that were... (0 Replies)
Hi,
When I am trying to boot my SUN Netra 240 Machine its giving some boot error.
> {1} ok boot -i
> Boot device: /pci@1c,600000/scsi@2/disk@0,0:a File and args: -i
> Boot load failed.
> The file just loaded does not appear to be executable.
> {1} ok
I tried to boot it from cdrom... (9 Replies)
Hi guys. I have an old Netra T1 that I'm hoping to recover here so I can twiddle around with Solaris 10.
It's been unable to power on despite issuing the "poweron" command or hitting the switch at the back of the server for some time. The LOM command "env" reports ALARM3 ON and everything else... (8 Replies)
Hello,
I wrote a script which monitor the keyswitch state repeatedly each 10 minutes.
I'm extracting the keyswitch status by using prtdiag.
The script works fine for Netra v440 , but I found that prtdiag under Netra 1290 don't give keyswitch status.
unlike Netra 440 server , I found that... (2 Replies)
guys - not sure where to post this one but i figured this was the likely spot.
i need a sun dvd slimline for netra t1. hcl matrix has this for production/manufac. number: X7288A / 540-5014.
anyone have a good spot to get this stuff? does anyone have an extra laying around to sell? i hate going... (2 Replies)
Hello, I'm trying to fix this server System Board (CPU/Memory Unit). The error indicates that its missing 3.3VDC. So far all the fuses and caps have been checked. I new at this type of machine, need help for idea on this system. Thank you in advance.
Vu (0 Replies)
