interface may off

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

2. UNIX for Dummies Questions & Answers

Interface

Hi All, How to check whether a Interface has a single port or dual port.Thanks in advance.

3. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ...

4. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you

5. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI...

6. UNIX for Advanced & Expert Users

interface problem

hi all, i have problem with my box, until now i can't investigate the root cause of my issue at my box. here the problem. i have a box as a squid server just forward all request packet from one interface and receive the packet then forward to client at the same interface. but after 5 hours i...

7. IP Networking

How to down interface without name

Hi, ifconfig -a return: eth0 Link encap:Ethernet HWaddr 00:09:3D:12:9D:5A inet addr:172.19.208.7 Bcast:172.19.208.63 Mask:255.255.255.192 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:211478649 errors:0 dropped:0 overruns:0 frame:0 ...

8. Solaris

no such interface

Hi Community, I've a problem with an interface of my Sun Workstation: when I try to plumb hme0 interface I see this output: # ifconfig hme0 <ip_address> netmask <mask> plumb #ifconfig: plumb: hme0: no such interface I've the same thing with dhcp service. could you provide any solution...

9. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt

LEARN ABOUT DEBIAN

netstat-nat

netstat-nat(1)						      General Commands Manual						    netstat-nat(1)

NAME

       netstat-nat - Show the natted connections on a linux iptable firewall

SYNOPSIS

       netstat-nat [options]

DESCRIPTION

       netstat-nat Displays NAT connections managed by netfilter/iptables which comes with the > 2.4.x linux kernels.

       The  program  reads  its information from '/proc/net/ip_conntrack' or '/proc/net/nf_conntrack', which is the temporary conntrack-storage of
       netfilter.

OPTIONS

       -h     displays help

       -n     don't resolve IPs/portnumbers to host/portnames

       -p <protocol>
	      display NAT connections with protocol selection (see /etc/protocols)

       -s <source host>
	      display connections by source IP/hostname

       -d <destination host>
	      display connections by destination IP/hostname

       -S     display SNAT connections

       -D     display DNAT connections

       -L     display only connections to NAT box self (doesn't show SNAT & DNAT)

       -R     display only connections routed through the NAT box (doesn't show SNAT & DNAT)

       -x     extended view of hostnames

       -r <src|dst|src-port|dst-port|state>
	      sort connections

       -o     no output header

       -N     display NAT box connection information (only valid with SNAT & DNAT)

       -v     prints version

FILES

       /proc/net/ip_conntrack or /proc/net/nf_conntrack

SEE ALSO

       http://www.tweegy.nl/projects/netstat-nat/
       http://www.netfilter.org/

AUTHOR

       netstat-nat has been written by D.Wijsman danny@tweegy.nl
       The manual page has been written by marceln@xs4all.nl

								     July 2002							    netstat-nat(1)

Solaris