interface may off


 
Thread Tools Search this Thread
Operating Systems Solaris interface may off
# 8  
Old 05-22-2008
Restart the in.routed daemon
check if there's any collisions using netstat -i
Login or Register to Ask a Question

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies

2. UNIX for Dummies Questions & Answers

Interface

Hi All, How to check whether a Interface has a single port or dual port.Thanks in advance. (5 Replies)
Discussion started by: rama krishna
5 Replies

3. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ... (3 Replies)
Discussion started by: mghis
3 Replies

4. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies

5. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

6. UNIX for Advanced & Expert Users

interface problem

hi all, i have problem with my box, until now i can't investigate the root cause of my issue at my box. here the problem. i have a box as a squid server just forward all request packet from one interface and receive the packet then forward to client at the same interface. but after 5 hours i... (1 Reply)
Discussion started by: tindasz
1 Replies

7. IP Networking

How to down interface without name

Hi, ifconfig -a return: eth0 Link encap:Ethernet HWaddr 00:09:3D:12:9D:5A inet addr:172.19.208.7 Bcast:172.19.208.63 Mask:255.255.255.192 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:211478649 errors:0 dropped:0 overruns:0 frame:0 ... (5 Replies)
Discussion started by: djbuly
5 Replies

8. Solaris

no such interface

Hi Community, I've a problem with an interface of my Sun Workstation: when I try to plumb hme0 interface I see this output: # ifconfig hme0 <ip_address> netmask <mask> plumb #ifconfig: plumb: hme0: no such interface I've the same thing with dhcp service. could you provide any solution... (1 Reply)
Discussion started by: Sunb3
1 Replies

9. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt (4 Replies)
Discussion started by: witt
4 Replies
Login or Register to Ask a Question
quaggaadm(1M)															     quaggaadm(1M)

NAME
quaggaadm - quagga routing daemon administration tool SYNOPSIS
quaggaadm [-e] zebra|ripd|ripngd|ospfd|ospf6d|bgpd|isisd DESCRIPTION
The quaggaadm command is provided as a simple wrapper to facilitate connection to the quagga daemons respective vty terminal telnet inter- faces, in a similar manner to zebraadm, which was provided as part of SUNWzebra. quaggaadm simply telnets the appropriate vty port for the specified daemon on localhost, and from there the user can update configuration for that daemon. Note that if the vty is disabled for the given daemon, quaggaadm will prompt the user to request enable. Note that to complete this operation, the user will require solaris.smf.manage.routing and solaris.smf.modify.routing authorizations. OPTIONS
The following command-line options are supported: -e Automatically enable the vty for the specified daemon. EXIT STATUS
The following exit values are returned: 0 Successful completion. !=0 An error occurred while obtaining or modifying the system configuration. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWquaggar | +-----------------------------+-----------------------------+ |Interface Stability |Evolving | +-----------------------------+-----------------------------+ SEE ALSO
quagga(1M), attributes(5), routeadm(1M) 02 Oct 2008 quaggaadm(1M)