10 More Discussions You Might Find Interesting
1. Solaris
We have 2 solaris 10 t5240 servers with static IP addresses on nxge0 I/F which were rebooted a few days back with a known good config that has been in place for years (for /etc/hosts, /etc/hostname.nxge0, /etc/netmasks, etc)
They are not using dhcp.
About the same time today, both of their... (7 Replies)
Discussion started by: hdatontodo
7 Replies
2. Solaris
I have installed Solaris 11.2 in VMware Player, networked in bridged mode. When Solaris uses DHCP everything is OK, I can reach internet, as well as other systems on my LAN. When I switch to static, I have connections to my LAN, but can not get to internet, the DNS resolution is somehow not... (2 Replies)
Discussion started by: migurus
2 Replies
3. Solaris
Hello All,
Problem is that redundancy doesn't work, probably a routing issue I need to get sorted out When 172.29.11.x net is down, neither node3 nor node4 is trying 172.29.12.x network,The problem lies in network 172.29.13.x
if 172.29.11.x network is down, node3/node4 should route to... (6 Replies)
Discussion started by: nadeemahmed
6 Replies
4. Solaris
ce0: flags=1100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4> mtu 1500 index 2
inet 10.162.212.132 netmask ffffff00 broadcast 10.162.212.255
ether 0:14:4f:55:82:9
ce1: flags=1100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4> mtu 1500 index 3
inet 10.231.11.232 netmask... (3 Replies)
Discussion started by: busyboy
3 Replies
5. Linux
Dear Sir
I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper.
I am having a problem, configuring static call routing on GNUGK
in the section
... (0 Replies)
Discussion started by: mfondoum
0 Replies
6. Solaris
Hi,
I have cloned a SOLARIS 8 (BLADE 150) Hard Disk and have put into other system. So, now how do I configure the NIC and assign static IP for this new machine ? (8 Replies)
Discussion started by: angshuman_ag
8 Replies
7. Solaris
I have a SUN ultra 5 machine running Solaris 6. it has two ethernet interfaces qe0 192.168.0.111 and qe1 192.168.1.111
the two subnets are 192.168.0.111 255.255.255.0
192.168.1.111 255.255.255.0
the specified routes are
add route -net 192.168.0.0 255.255.255.0 192.168.0.111
add route... (3 Replies)
Discussion started by: adol65
3 Replies
8. Solaris
Hi,
I got problem of Sun Solaris 8 routing.
IP of SunA is 10.16.64.164, and have routing table:
10.16.64.0 10.16.64.164 U 1 19236 bge1
10.6.0.0 10.6.0.3 U 1 16534 bge0
224.0.0.0 10.6.0.3 U 1 ... (4 Replies)
Discussion started by: milo
4 Replies
9. Solaris
Hello,
Iam having problems getting more then one ip to work here is my setup!
Hostname: nexus
NIC: e000g1
(example ips)
My ips 80.80.80.15 to 80.80.80.20
Defaultrouter 80.80.80.1
nameservers 80.80.80.100 and 80.80.80.200
How would i do this? Any help would be mutch appriciated!... (7 Replies)
Discussion started by: empty
7 Replies
10. IP Networking
hi,
below is the situation:
my server is in 128.10.200.xxx network.
i have a solaris computer running in a subnet. this computer got 2 nic card.
1 is 172.18.198.xxx , another 1 is 10.100.xxx.11
there is a machine stick with this computer, ip is 10.100.xxx.12
so, 10.100.xxx.11 and... (3 Replies)
Discussion started by: kyhah
3 Replies
DNROUTE(8) System Manager's Manual DNROUTE(8)
NAME
dnroute - DECnet Routing Daemon
SYNOPSIS
dnroute [options]
Options:
[-dvV2Dtnhr]
DESCRIPTION
dnroute is a daemon that manages the DECnet routing tables to provide a simple
but probably useful routing policy.
dnroute listens for incoming routing messages and adds routes in the kernel for non-local areas that it sees. Routes will be modifed
according to these messages so that the lowest cost route that is up will always be used. Routes to locally accessible nodes (it those in
the neighbour table) will also be added. If you want to keep manual control of the route to a particular area, then add a line into
dnroute.conf. eg:
manual 26
will disable dnroute's setting of routing tables for that area. dnetinfo will still show the route that would have been set with (M) on the
line to show it has been overidden.
To implement its routing policies dnroute assumes that all interfaces on the system have a cost of 4. To change this add lines in
/etc/dnroute.conf for each of the interfaces you need to change. eg
eth0 6
eth1 8
tap0 10
A script called dnetinfo is provided that gets the routing information from dnroute and displays it on stdout in a format similar to the
VMS command SHOW NET/OLD.
OPTIONS
-d Don't fork and run the background. Use this for debugging.
-v Verbose. Log route changes to syslog.
-D Debug log. Writes debugging information to stderr. Only useful with -d.
-h -? Displays help for using the command.
-r Send DECnet routing messages showing the state of local nodes.
-2 Send DECnet level 2 (area) routing messages. Implies -r.
-t <secs>
Timer to send routing messages on. Defaults to 15 seconds.
-n Do not set up routes or send routing messages, just monitor the network. Useful for testing.
-V Show the version of dnroute.
SEE ALSO
dnetd.conf(5), ip(8)
DECnet utilities March 30 2006 DNROUTE(8)
