10 More Discussions You Might Find Interesting
1. Solaris
Hello all,
I am trying to learn about Solaris and Sun systems so I purchased a SunFire 280r running Solaris 9 with a disk array from eBay. The system had no video card so I purchased a PGX32 card for the PCI slot and installed it.
The problem is I have no video what so ever. I am familiar... (3 Replies)
Discussion started by: FTBTX
3 Replies
2. Solaris
I have 2 solaris boxes and trying to connect to D1000 to do clustering. I put the U cable to see the disks from both side, but I can't see any of the disks when I use format command. How can I verify that differential card is installed and configured correctly? Thanks in advance. (12 Replies)
Discussion started by: mokkan
12 Replies
3. Solaris
Hi all,
i have configured my solaris 5 .10 for internet connection by editing the files /etc/hosts/,/etc/resolve.config,/etc/defalutrouter and nsswitchconfig .
during installation i was not requested for ip adddress even i plugged network cable.
am i need to install any network card... (2 Replies)
Discussion started by: srikanthg
2 Replies
4. UNIX for Advanced & Expert Users
hello, i have a dell Poweredge 2950 ( Server ) and an IBM storage device DS 3000 family ( Storage ) . I am supposed to link the IBM storage device to the Dell Poweredge via "Emulex 4Gb Fibre Channel Host Bus Adapter".
I have put the addapter card in my server and connected it to the storage.... (3 Replies)
Discussion started by: nux007
3 Replies
5. Solaris
Hi,
I'm connecting a Solaris 10 server to a Netapp filer with two single port Emulex (Sun StorageTek PCI-X Enterprise 4GB FC HBA) HBAs. After physically installing both these HBAs what do I ned to do within Solaris 10 to enable them and configure them with persistent bindings.
Do I need... (6 Replies)
Discussion started by: gwhelan
6 Replies
6. UNIX for Advanced & Expert Users
Hello!
I'm having problems to install Emulex fibrechannel card drivers to a HP DL580 G5 running Solaris 10 x86_64. Any of you guys had this problem or knows the answer? =)
cfgadm gives me the following info, which seems to say that it is ok?
But the card has'nt logged into the switch... (0 Replies)
Discussion started by: Esaia
0 Replies
7. UNIX for Advanced & Expert Users
HI,
I am trying to install Symbios SCSI PCI adapter in Ultra10 but unable to configure it. Getting following errors
genunix: NOTICE: glm0: fault detected in device; service still unavailable
genunix: NOTICE: glm0: Symbios PCI device (1000,3) not supported.
Anyone has an idea, how to resolve... (1 Reply)
Discussion started by: s_aamir
1 Replies
8. IP Networking
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies
9. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
10. UNIX for Dummies Questions & Answers
hi all
We went to analyze a intel based server installed with Solaris 8 .previuosly on that machine Rhat 7.1 was loaded and working fine in the N/W. After we loaded Solaris 8 it got automatically rebooted when it comes to the Gui mode.The same happened thirce and we opted out to load without... (5 Replies)
Discussion started by: edwin_francis
5 Replies