Prtdiag is Not working in Solaris 8 Ver

9 More Discussions You Might Find Interesting

1. Solaris

prtdiag -v troubleshooting

selected lines from the output of the "prtdiag -v" command on a T5240 SUN server running Solaris 10. Are the following known as FRU names and what do they mean? MB/CMP0/BR0/CH0/D0 MB/CMP0/BR0/CH1/D0 SYS/FANBD0/FM0/F0 SYS/FANBD0/FM0/F1 SYS/MB/CMP0/BR1/CH0/D1 ...

2. Solaris

prtdiag

Hi everyone, Please can you tell me what kind of memro we are talking about when we run : prtdiag -v Memory size: 98016 Megabytes Thank you

3. Solaris

prtdiag output for Solaris on Fujitsu hardware shows vendor as Sun Microsystems

Hello, I was under the impression that the Header of the prtdiag output shows the hardware vendor information in the section between System Configuration and sun4u/sun4us. But on some Solaris machines which are running on Fujitsu hardware, the vendor is shown as Sun Microsystems in this...

4. Solaris

Executable compiled on solaris 10 not working on solaris 9

Hi I compiled an executable on Solaris 10 which creates semaphore ( semget) but it didn't work on solaris 9 , while it is executing sucessfully on solaris 10. It is throwing the system error that Invalid arguments ( system error 22) on solaris 9. the ldd for the executable on two servers is as...

5. Solaris

SF T2000 prtdiag problem

Hi, a couple of T2000 servers did not show the component status and the output was too short. There was a patch that needed to be installed. I also updated to the latest recommended patch cluster and OBP patch. After reboot/restart of picl, it worked ok for a couple of weeks. Then suddenly it went...

6. Solaris

prtdiag - Segmentation Fault

Hi, Recently installed a Firmware patch on T5120 (solaris 10,138888-03). The patch installation was Success and system came up fine as well. My apps are running fine too. Problem is prtdiag does not work as it used to earlier. the output is very different from other t5120s I have and...

7. Solaris

prtdiag and memory banks

hi, we have an e6900 and my sys admin says that the number of processors and memory were reduced to 4 and 8GB. However, a prtdiag |grep Memory returns 16GB of memory. So what is my system's memory? psrinfo returns 4 online and 4 offline CPUs. Thanks. Kumar

8. Solaris

SOLARIS/BEA WEBLOGIC ver.8.1

Hello all, I am having a little issue with BEA webloigc server Version 8.1, previously, we we confugred we where able to Grep processes for BEA and we could get the processes listed now I am only able to see the start weblogic script process. the weblogic server is up and running and performing its...

9. UNIX for Advanced & Expert Users

Sun Solaris "prtdiag -v" on redhat

Does anyone know of a command or list of commands that shows the same amount of detail as prtdiag -v for redhat linux?

LEARN ABOUT XFREE86

install-solaris

install-solaris(1M)													       install-solaris(1M)

NAME

       install-solaris - install the Solaris operating system

SYNOPSIS

       install-solaris

       install-solaris	invokes  the  Solaris  Install	program. Depending on graphical capability and available memory at the time of invocation,
       install-solaris invokes either a text-based installer or a graphical installer.

       The following minimum requirements for physical memory dictate which features are available during installation:

       For SPARC machines:

       128 MB

	   Minimum physical memory for all installation types

       128 MB

	   Minimum physical memory required for windowing system

       384 MB

	   Minimum physical memory required for graphical-based installation

       For x86 machines:

       256 MB

	   Minimum physical memory for all installation types

       256 MB

	   Minimum physical memory required for windowing system

       512 MB

	   Minimum physical memory required for graphical-based installation

       In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number  of  fea-
       tures available.

       install-solaris	exists	only  on  the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the  for more
       details.

       install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
       installation media. Refer to the  for disk space requirements.

       Refer to the  for more information on the various menus and selections.

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWcdrom  (Solaris instal-  |
       |			     |lation media)		   |
       +-----------------------------+-----------------------------+
       |Interface Stability	     |Evolving			   |
       +-----------------------------+-----------------------------+

       pkginfo(1), install(1M), pkgadd(1M), attributes(5)

       It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.

								    23 Sep 2005 					       install-solaris(1M)

Solaris