I want to develop application which will discover the information about the cluster and how many nodes are connected to that respective box.
Also would like to find out other information about cluster environments.
Also please send me material if you guys have.
Hello experts -
I am planning to install a Sun cluster 4.0 zone cluster fail-over. few basic doubts.
(1) Where should i install the cluster s/w binaries ?. ( global zone or the container zone where i am planning to install the zone fail-over)
(2) Or should i perform the installation on... (0 Replies)
hi ,
i installed sun cluster on 2 nodes , and i have one shared disk , problem is i couldnt able to deport and import shared disk group properly.
thanks for ur help
ravi sankar (2 Replies)
hi ,
i have to find get VxVM cluster information , with using solaris command .
if its not possible , to get information that VxVM cluster service is enable/disabled? (3 Replies)
Yesterday my customer told me to expect a vcs upgrade to happen in the future. He also plans to stop using HDS and move to EMC.
Am thinking how to migrate to sun cluster setup instead.
My plan as follows leave the existing vcs intact as a fallback plan.
Then install and build suncluster on... (5 Replies)
Hi,
I am getting these messages constantly at random times there is not visible impact but would like to know what these messages mean?
Cluster.RGM.rgmd: resource group
on node change to RG_ON_PENDING_R_RERT
Cluster.RGM.rgmd: resource group on node change to RG_ONLINE (1 Reply)
hi
can u please send me how to configure cluster in x86 machines. i am using VM ware. Is there any difference in X86 and SPARC cluster installations
please help me
thaks to all (1 Reply)
Hi,
Can you please help me to locate tape drives on Sun Server and the capacity of the tape drive.
I am managing a Sun 4u server.
Need this urgently.
Regards,
Vivek (2 Replies)
clsetup(1CL) Sun Cluster Maintenance Commands clsetup(1CL)NAME
clsetup - configure Sun Cluster interactively
SYNOPSIS
/usr/cluster/bin/clsetup -V
/usr/cluster/bin/clsetup -?
/usr/cluster/bin/clsetup [-f logfile]
DESCRIPTION
The clsetup command provides the following configuration capabilities, depending on what state the cluster is in when you issue the com-
mand. The user must be superuser to run this command.
This command has no short form.
o When you run the clsetup command at post-installation time, the command performs initial setup tasks, such as configuring quorum
devices and resetting the installmode property. If you deselected automatic Quroum Configuration when you created the cluster
using either scinstall or the cluster create command, then you must run the clsetup command immediately after the cluster has
been installed. Ensure that all nodes have joined the cluster before you run the clsetup command and reset the installmode prop-
erty.
If you used automatic quorum configuration when you created the cluster, you do not need to run the clsetup command after clus-
ter installation. The automatic quorum configuration feature also resets the installmode property of the cluster.
You can issue this form of the clsetup command from any node in the cluster.
o When you run the clsetup command during normal cluster operation, the scsetup command provides an interactive, menu-driven util-
ity to perform cluster configuration tasks. The following are some of the cluster components which this utility administers:
o Quorum
o Resource groups
o Data services
o Cluster interconnect
o Device groups and volumes
o Private hostnames
o New nodes
o Other cluster properties
You can issue this form of the clsetup command from any node in the cluster.
o When you run the clsetup command from a node that is in noncluster mode, the clsetup command provides a menu-driven utility for
changing and displaying the private IP address range.
You must reboot all nodes into noncluster mode before you start this form of the clsetup utility.
OPTIONS
The following options are supported:
-?
--help
Prints help information for the command.
-f logfile
--file logfile
Specifies the name of a log file to which commands can be logged. If this option is specified, most command sets generated by clsetup
can br run and logged, or just logged, depending on user responses.
-V
--version
Prints the version of the command set. No command line processing will be performed and the command will not enter into its interactive
menu.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWsczu |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
SEE ALSO Intro(1CL), cldevicegroup(1CL), clnode(1CL), clquorum(1CL), clreslogicalhostname(1CL), clresourcegroup(1CL), clresourcetype(1CL),
clressharedaddress(1CL), cluster(1CL), cltelemetryattribute(1CL)Sun Cluster 3.2 5 May 2006 clsetup(1CL)