Hicksd8 found it all by himself. If you don't get an answer immediately, don't panic, just wait -- we have many knowledgeable people, but they aren't active 24 hours a day.
If you have Solaris installation media (Solaris 8, 9, 10 or 11 SPARC version, of course) you can boot into single user with:
that will allow you to see that the hardware is capable of running Solaris.
If you:
it will boot and enter the Solaris install routine.
Your terminal emulator is connected to the SC after boot. If you want to talk to the main processor (after you've 'poweron' and installed Solaris) you can:
to do that and get a login prompt.
When connected to main processor (Solaris) you can type
to return to the SC.
There are a number of downloadable manuals on the web for the Netra 240 (service, install, admin, etc) so I suggest that you get your paws on those if you haven't already.
EDIT: As pointed out by Gull04 below, the Netra 240 cannot run Solaris 11.
I'm putting my thoughts in writing here. Unfortunately, I cannot derive a definitive answer from the information that you have provided so I just resort to a series of statements in the hope of it being helpful.
I notice from one of your screen captures that the system date is 1/1/2000. Is the backup battery on the mobo dead? Has this hardware been idle for ages?
Did you have to login to the SC before it would let you do anything? userid/passwd combination? If the hardware has lost all its memory due to a dead battery then the userid/passwd combination to use will be admin/changeme or root/changeme.
This warning implies that your poweron command is not being executed due to no valid SC login:
Quote:
Warning: the poweron command is being ignored because the password for admin is not set.
The 'poweron' command turns on the whole main processor. AFAIR, there are no individual power commands for individual components. However, if your 'poweron' command is not executing then there is no surprise that the DVD is dead. If 'poweron' is doing its job then perhaps the DVD is faulty? Remove it and test on other hardware.
Last edited by hicksd8; 11-26-2018 at 01:10 PM..
These 2 Users Gave Thanks to hicksd8 For This Post:
Clock Stable w/ New Battery, "Break" command & USB Port Not Working.
Dear Hicksd8,
OK, new battery is keeping the system clock stable. Thanks for the heads up Hicks! Here is the latest SC action to celebrate:
There was some headache from mushy tiny battery positive terminals. To get the little new battery going, I had to slide in some wires under them and press them down with a tiny piece of electrical tape. I could be useful for somebody else in these situations, so I took pictures with my phone. Wire thickness must be right, and no aluminium foil did not work, in my case at least.
However "poweron"-"poweroff" problem is the same. Still thinks systems is not powered and break command does not work. DVR-ROM Still does not power up or respond to front keypress. I tried the USB ports with a brand new Sandisk memory stick, tested on 2 machines. Both plugging during operation and plugging before power up did not make it show on FRU list with "showfru" command.
Which brings us to motherboard jumper situation. Below are the info available in the manual about Netra240 motherboard jumpers:
Here is an overall picture of the board with current jumper positions:
I will follow with an ordered picture gallery of jumpers taking care to show jumper number and whether they are set or not.
Thanks again for your smart electronics probing from afar. Yes you are right, the coin battery is most probably dead. I bought this from a government surplus liquadator from Ankara, it should have been sitting somewhere for long. Its a 2006 model, I think. Battery must also be 12 years old. Seller did promise to change any parts if necessary. That we have in pocket, but he is just 400 miles from here. The battery holder seems a little delicate, I did try to take that out when it first arrived. I will have to take that out somehow now that it is relevant.
When I first entered SC, yes there was no password. But I can set a password, after that it does allow me to use the "poweron". That command again starts the main air blower inside. But then "poweroff" does respond with a "power is already off". If changing that battery doesn't solve the issue, we can try loading an OS through the 2 USB slots hopefully.
Another idea is to check the jumpers on the motherboard, IMHO. I found the table for it in the manuals. I will photo their current setup for you to inspect, in any case.
BTW, just received the "High Noon" book about McNealy from your country, the good old UK. A University of Derby discard in perfect condition. I just love reading self-promotion volumes of silicon valley boys paid for their personal advertisements. Just gobbled up Dr. David Yen's book, named "Under the Sun: My 20 years in Sun Micro.." the previous night in one long sitting. That was heady. This old clunky machine stimulates the unsatisfied electronics engineer in me, whether works or not. My favorite classes were Digital Design and Computer Architecture, both using wonderful books of Morris Mano (photocopies of course) when I was in Istanbul Tech. Baah, the good ole days man...
Just a quick bit of info, the server will only run Solaris up to and including Solaris 10 1/13 - it will not run 11 as the SPARC IIIi processor is not supported by the OS.
It's why my v250's at home are still at Solaris 10.
Regards
Gull04
These 2 Users Gave Thanks to gull04 For This Post:
Thanks Gull04. Good to save the time beforehand, and good to know I didn't burn that Solaris 10 for Sparc DVD for nothing. Will stay with that. Expecting an XVR-100 graphics card which has drivers for it built into Solaris 10, right?
Greetings,
I hope my post finds you all OK,
I have a Netra240 server in an HLR inside a wireless CDMA Exchange, it works as a Hard Disk Unit (HDU) as shown in Local Management Terminal (LMT) as show in the picture 1 attached.
The power went down because of a power failure in main UPS, when... (2 Replies)
I have this code:
#!/bin/sh
awk 'BEGIN
NR == 2
repl = "PHI"
$4 = repl
print $0 'dryloop.txt
and this code:
#!/bin/sh
sed -e '1s/\|$/\|COMID\|/g' -e 's/^087.*$/&PHI\|g' hl.dsldryloop > textdry.txt
My code won't work. I want to change the COMID of lines starting with 087 .
this is my... (15 Replies)
When i run this command, everything is ok. The file can be email and attached but soon after i download the file, the file cant be read. It's seem corrupted. Totally cant be read although i'm using context or wordfile. Original file generated at ek_bkup/alert/tbspace_datafile.log is OK.....
... (7 Replies)
Hi,
I need your help guys. I have two data files, namely 101.amberized.pdb & 101.pdb .
Now I want to replace the whole 3rd column of 101.amberized.pdb with the 3rd column of 101.pdb file. How do I do it in shell?
Thanks in advance
Parimal (11 Replies)
I have a list of variables: ss1, ss5, ss6, ss8, st2 etc. (these values are not fixed, configurable). Now, I have assigned ss5=”test”. And I want to search in the list for the string “test” to know which variable is having the value “test”. Can u pls tell me how to do this? (10 Replies)
Hi every one
I have got very very bad Email, My question is:
How can I get all information about that f*** Email, I do mean
IP,reall name, Adress, user name, password etc... I wonder if there is any program or website that I can see that email, help me please
When I used windows Xp(old... (2 Replies)
Hi, I'm a newbie.
I need help on my first assignment in UNIX.
1. How do I determine the number of non-empty directories?
I was told to create a variable ARCHIVE, which points to the directory that contains the archive of the messages. But I'm so dumb and I don't even know how to do this.
2. In... (1 Reply)
we hv a big enviroment networked.
we use squid proxy.
access allowed by src address previously.
we have win2000 network with ads.
my requirement is the proxy should allow domain users only for access.
how can i map my windows userdatabase with squid
is there any thing specific which has 2 b... (1 Reply)