Solaris 10 boot problem - ERROR: Last Trap: Fast Data Access MMU Miss
Hello,
We have a T5140 server with Solaris 10 and its suddenly throwing "segmentation core" when I login into the server and not showing any output for commands like df, mount etc. so I had to reboot the server to fix this issue. Please note that there's no boot disk mirroring.
But unfortunately the server would not come up (I think it loads kernel and after a while, throws the below error)
and comes back to OK prompt
I have gone through few threads that address this issue but none of them helped. I tried show-disks (no errors), probe-scsi-all with all OK except one error ERROR: /pci@400: Last Trap: Fast Data Access MMU Miss and I tried test-all which shows all OK and even tried reset-all but no luck.
Finally I tried boot -F failsafe which gives me a shell as below
Not sure how to proceed from here? should I try installboot or will it break further? Unfortunately, We have only hardware support (no OS support from Oracle). Not sure if it's a hardware issue at pci@400 controller/boot drive?
Hi
I have a problem on a server, when he boot I have this type of message loop, do you know what it corresponds to ?
( requesting internet Adress for 0:3:ba:fa:33:91 )
Regards
Sun Fire V240, No Keyboard
Copyright 2007 Sun Microsystems, INC. All rights reserved.
openboot 4.22.33,... (10 Replies)
Hello everyone,
This is the first time I am installing Solaris. I have SunBlade 1500 Wrkstn. I installed Solaris 10 Sparc.
The installation went successfully but I don't get the login screen. I get the following error message:
Boot device: disk:a File and agrs:-
Data Access Error
Ok
... (4 Replies)
hello,
before i have install solaris 9, is good.
I would like to install Ubuntu 10.04 on a Sun Blade 150 blade.
I create cdrom iso burning with a 10x
was open I made a boot ok: boot cdrom
I get the following error:
fast data access mmu miss
i do
probe-ide all
reset-all
always
... (2 Replies)
Hi All
We have the Sun Solaris server ... Got a power cut suddenly .... Crash happened to the system almost
You can access through Termnl .. But it seems he did not boot ... How to Make the process of the boot correctly without losing information
Thanks for all (3 Replies)
Hi All ,
I am unable to reinstall the OS on my Ultra Sparc 10. After the 1st CD is loaded when it goes for reboot its goes to ok prompt an its unable to boot.
What could be reason for this behavior? while loading the OS its seems fine but unable to boot!!
Then i tried changing the... (2 Replies)
Hi
using solaris 5.8 on UltraSPARC-IIi 360MHz.
I know it is an old hardware but similiar hardware is running fine. here is the issue,
System booted : works okay for some time then display was hung so system was rebooted ..it gave data access error. again rebooted and it came up... (6 Replies)
Dear all,
Every time I boot my Ultra 60, after initializing the memory I always have to type boot at the ok>
Rebooting with command boot
Boot device: disk0 File and args :
Trap 3e
(0) ok
I've tried to re-installed the machine but result is the same...
What would be the problem?
... (4 Replies)
Our V480 w/ Solaris 9 would not boot properly. After recreating the LUNs on our StorEdge A1000, and then performing a reboot, the machine just keep cycling through the boot process. No error messages, it keeps trying to reboot over and over again.
Any ideas?
We managed to do a stop+a and... (6 Replies)
When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error.
cannot find mis/krtld
boot error loading... (0 Replies)
I couldnt get my hands on my solaris 2.6 cd soo i used solaris 7 cd to boot to single user mode. I typed
boot cdrom -s
it bought me to my root prompt , but when i typed fsck.....nothing happened. It was as though it couldnt go ahead with fscking. it just bought up the prompt again,... (1 Reply)