hello, I have a problem when configuring the network at the LDOM level, on a SPARC-Enterprise-T5120 machine
The network goes through VLAN 503 (level, network tagget)
And I need to give network to the guest domain: madarrwebsol10
I hope someone can bring some light ....
Excuse my English ...
****
VLAN is taggint for VLAN503 on net0
Now, agregate virtual vswitch
reboot and boot Guest Domain-.... with Solaris 10
Do not create vlan interface (dladm create-vlan ..).
Delete that interface.
If using VLAN tagging add the virtual switch in this manner :
Then add tagged interface into guest domain :
This way, tagging will be done by hypervisor vnet/vsw, not inside guest domain.
Guest domain will be in VLAN 503 exclusively.
Good practice would be to aggregate all four network ports into one aggr0 then use that for as net-dev.
You will get redundancy in case of failure, as well as combined bandwidth of 4 network ports.
Also, on that aggregated interface specify as many VLAN ids that are used in your environment when creating VSW.
The switch network ports should be configured as trunk.
You only need VLAN (dladm create-vlan) interface for the hypervisor IP address.
I would recommend using seperate VLAN id for hypervisor ip address (security wise).
Creating VSW with name of virtual machine is not proper naming.
Human is for instance : lab-vsw0, prod0-vsw or similar descriptive name.
You will use that virtual switch for other machines as well, so naming it after one ldom is not so straightforward.
Be careful about naming in Oracle VM server hypervisor, it will allow you to name anything you like as you like it.
When you have a lot of machines, naming policy will save you extra investigation what is mapped where (disks, vsw to ldom etc.)
I have a Sun T4-1 running Solaris 11.4 with a static IP 192.168.0.183. On this machine is a Solaris 10 LDOM with a static IP of 192.168.0.78. The other day I had to stop the LDOM to do a memory reconfigure. When I rebooted it I got an error that the IP 192.168.0.78 was already in use and so... (4 Replies)
I'm really stuck here. I've created an LDOM on a SPARC T4-1 with Solaris 11.4 to run a copy of Linux for SPARC. I got the Linux ISO installed and Linux itself installed and booted OK. The only thing is is that there's no networking available in the Linux guest.
This question is basically the... (7 Replies)
Hello Guys,
Can some help me with a configuration from 2x10g cards to 4 Ldoms and a Vlan configuration,
Solaris 11
dladm show-phys
LINK MEDIA STATE SPEED DUPLEX DEVICE
net0 Ethernet up 1000 full ixgbe0
net1 Ethernet ... (2 Replies)
Hi,
Our existing environment is having primary domain and 3 guest domains are running over it. See the attached image.
Now we want to add a new primary virtual switch and move LDOM3 to be connected with new primary switch.
So, I am not sure how to achieve this because. If I remove the... (7 Replies)
I have an Oracle VM set up with 1 virtual disk. I am trying to add 2 new disks to it. I was able to successfully add 1 (it appears when I run "format" in the VM) but when I add the second and third disks they do not appear in my VM.
Here are the commands I ran:
ldm add-vdsdev... (3 Replies)
Solaris for Sparc 11.1 with the latest patches. Created a Guest LDOM with two vnet's net0 and net1, installed a guest whole root, ip exclusive zone that I want to be able to utilize DHCP. I have been able to create the zone but unable to get it to boot because I am unable to assign an anet to it.... (4 Replies)
Trying to set or modify the randomly set hostID of a Solaris 10 virtual/guest machine that I installed on a Windows-XP host machine (using Virtual Box 4.1.12).
I was able to set/modify the hostname of the Solaris 10 virtual/guest machine during installation as well as via the Virtual Box... (4 Replies)
I want to know potential problems with the following scenario OR if it is an ok way to have my network setup:
I have 2 WAN connections to the internet. I have each WAN connection plugged into its own router. Router DD-WRT is gateway for servers (192.0.10.50). Router Tomato is gateway for pc's... (1 Reply)
Hi,
I have a question on web servers and network switches.
Why a network switch should support certificate management, that means generating public and private keys... installing a certificate etcetra.
Regards
Chaitanya. :b: (4 Replies)